manualshive.com logo in svg

Weir Roto-Jet RO III 3x2, Disassembly-Assembly Manual

Share
Download
Weir Roto-Jet RO III 3x2 Disassembly-Assembly Manual Download Page 24

 

RO/ROH 3x2 

20 

2.8.4.13. 

Replace seal hub (55), if required seal hub radial runout must be 

checked and adjusted as required.  reference section 2.8.6 for seal hub 
replacement. 

 

2.8.4.14. 

Slide seal plate (70) into endbell (26) with seal outward and drain 

hole to bottom of pump.  Install 4 socket head capscrews and hand 
tighten.  Mount dial indicator on seal hub to measure radial runout of the 
seal plate register diameter (see figure 2.8 "B").  Max TIR = .002 inch 
(.051 mm).  Slowly turn hub using pump shaft.  Adjust the seal plate by 
gently tapping it on O.D. until the runout is to spec.  Then tighten the 4 
socket head capscrews (71) to 20 ft. lbs. (27 mm), then tighten the 3 set 
screws (80) to 6 ft. lbs. (8mm).  Recheck runout, repeat if necessary. 

 

2.8.4.15. 

Slide mating ring (69) and o-ring on hub (29).  Install hub nut (55) 

and torque to 26 ft. lbs.  (left hand thread). 

 

2.8.4.16. 

Re-assemble per section 2.8.7. 

 

2.8.5.  Rotating Single Seal 3x2 Pump  (standard seal configuration, reference figure 

2.6.2) 

 

2.8.5.1.  Remove Seal (75) from hub (29). 

 

2.8.5.2.  If seal is to be reassembled in unit, note the seal setting before 

removing seal.  On 3-1/2" seals equipped with balance sleeve - remove 
seal, sleeve and o-ring at this time.  On 3-1/4" seals remove seal and o-
ring. 

 

2.8.5.3.  Remove (4) socket head capscrews (18) and then remove seal mating 

plate (70)/mating ring (78) assembly from endbell (26). 

 

2.8.5.4.  Remove mating ring (78) and o-ring (69) from seal mating plate and 

clean mating ring cavity. 

 

2.8.5.5.  Seal hub (29) replacement, if required, for replacement of damaged 

hub.  See section 2.8.6. 

 

2.8.5.6.  Install new o-ring (69) in seal mating plate (70) and apply light oil to seal 

cavity. 

 

2.8.5.7.  Install seal mating ring (78) in seal mating plate (70). Caution to be 

taken to avoid chipping face. 

 

2.8.5.8.  Slide seal mating plate (70) into endbell (26) with seal facing outward.  

1/2" hole to bottom of pump.  Install 4 socket head capscrews (71), 
torque to 20 ft. lbs. 

 

2.8.5.9.  Slide seal (75) onto hub (29) and set to previous setting or 

manufacturer's recommended height.  Using set screws, torque to 40 
in. lbs. 

 

Summary of Contents for Roto-Jet RO III 3x2









































Reviews:

No comments

Brands by name

Popular brands

Load more brands