4
5
6 V1.2 / 2021-07-06
Note about behavior of failure relay (triggerable by power failure or port link down):
Relay contact is closed if the device is powered-off.
Relay contact is open if the device is powered-on and no alarm conditions exist (neither
Power Failure Alarms nor Port Link Loss Alarms are activated (Web menu Warnings
Fault Relay Alarm).
Relay contact closes if any of an activated alarm condition happens.
9. Communication Connections
Switch
IE-SW-AL18M-16TX-2GC
is equipped with following communication interfaces:
16 x
10/100Base-T(X) ports
2 x
Ethernet-Combo-Ports, that can be used either as 10/100/1000BASE-T(X) ports
or alternatively as 100/1000BASE-X ports with respective SFP Transceivers
Please only use cables suitable for the respective type of communication and ensure that
signals are protected from possible interference.
9.1
10/100BASE-T(X) RJ45 Ports
The 10/100BaseT(X) ports located on Ethernet Switch’s front panel are used to connect to
Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. Auto MDI-X ensures that both wiring-schemes are supported
(Automatic crossover function).
10/100BASE-T(X) RJ45 Pinouts
MDI Port Pinouts
MDI-X Port Pinouts
8-pin RJ45
Pin
Signal
Pin
Signal
1
Tx+
1
Rx+
2
Tx-
2
Rx-
3
Rx+
3
Tx+
6
Rx-
6
Tx-
9.2
Combo-Ports
The switch is equipped with combo ports that can be used either as 10/100/1000BASE-T(X)
ports with RJ45 connector or with optional SFP transceivers (mini GBIC) for 100/1000BASE-X
(e.g. for connections with fiber optic technology over long distances). For correct function,
please note that only one function of a combo port may be used and connected at a time. The
RJ45 port can only be used if no SFP module is plugged in.
9.2.1
1000BASE-T Ethernet Port Connection
1000BASE-T data is transmitted on differential TRD+/- signal pairs over copper wires.
Pin
Signal
1
TRD(0)+
2
TRD(0)-
3
TRD(1)+
4
TRD(2)+
5
TRD(2)-
6
TRD(1)-
7
TRD(3)+
8
TRD(3)-
9.2.2
100/1000BASE-X SFP fiber optic port
The 100/1000BaseSFP type slots require either a 100BaseSFP or a 1000BaseSFP fiber
transceiver (mini-GBIC) to work properly. Please only use SFP modules and cables that are
compatible with each other to establish an optical connection.
LC-Port Pinouts:
LC-Port to LC-Port Cable Wiring:
For a
LC-Port with separate Transmit and Receive Port
please r
emember to connect the Tx
(
transmit) port of Device-1 to the Rx (receive) port of Device-2, and the Rx (receive) port of Device-
1 to the Tx (transmit) port of Device-2.
9.3
RS232 Console Port
The RS232 Interface with RJ45 connector can be used to access the switch console for
configuration.
Pinouts Serial
Console Port:
10. User Management
10.1 Device Access (Login to Web Interface)
The Web interface of the Switch can be accessed via following factory default settings:
IP address / Netmask:
192.168.1.110 / 255.255.255.0
User name:
admin
Password:
Detmold
Connect the PC to any Ethernet port of the managed Switch and set the PC’s IP
address to a free one of range 192.168.1.0 / 255.255.255.0
Start a web browser and enter the IP address of the connected Switch into the
browser’s address line (http://192.168.1.110). After the appearance of prompt (login)
enter the login credentials. After confirmation of your input with "OK" the home page of
the switch will be displayed.
Note:
For more detailed information about configuration and use of the device features
please read the downloadable manual from Weidmüller’s website (Product catalogue
Automation & Software
Industrial Ethernet
Advanced Line managed Switches
Select Product
Click and expand section „Downloads“
Download needed software
or documentation).
10.2 Reset Button
Press reset button for 2 to 3 seconds to reboot the switch (Warm Start).
Press reset button for >= 5 seconds to reset the switch to factory default settings.
11. LED Indicators
The front panel of the Ethernet Switch contains several LED indicators. The function of
each LED is described in the table below.
LED
Color
Status
Description
PWR1
Green
On
Power is being supplied to power input PWR1.
PWR2
Green
On
Power is being supplied to power input PWR2.
R-MSTR
(Ring Master)
Green
On
Is Ring Master of an enabled O-Ring.
Ring
Green
On
O-Ring redundancy is enabled.
Blinking Ring structure is broken (No redundancy).
FAULT
Amber On
Fault Relay indication for Power failure and
Port link loss.
LNK/ACT
(Ports 1 -16)
Green
On
Port’s link is active.
Off
Port’s link is inactive.
Blinking Data is transmitted.
Full / Half
Duplex
(Ports 1 – 16)
Amber
On
Port is set to Full Duplex Mode.
Off
Port is set to Half Duplex Mode.
Blinking Packet collisions detected.
LNK/ACT
RJ45 Combo
Port G1/G2
Green
ON
Port’s link is active.
OFF
Port’s link is inactive.
10/100/1000M
RJ45 Combo
Ports G1/G2
Amber
On
Port speed is 100 Mbps
Off
Port speed is 10 or 1000 Mbps
LNK/ACT
100/1000Base
-X Combo
Ports G1/G2
Green
On
Port’s fiber link is active.
Off
Port’s fiber link is inactive.
12. Specifications
Technology
Ethernet Standards
IEEE 802.3 for 10BASE-T
IEEE 802.3u for 100BASE-TX and 100BASE-FX
IEEE 802.3ab for 1000BASE-T
IEEE 802.3z for 1000BASE-X
IEEE 802.3x for flow control
IEEE 802.3ad for port trunk with LACP
IEEE 802.1D for STP (Spanning Tree protocol)
IEEE 802.1w for RSTP (Rapid Spanning Tree protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1p for Class of Service
IEEE 802.1Q for VLAN Tagging
IEEE 802.1X for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
Processing Type
Store and Forward
MAC Table size
8K
Packet buffer size
1 Mbit
Backplane bandwidth
7.2 Gbps
Interfaces
RJ45 Ports
16x 10/100BASE-T(X) auto negotiation speed, F/H duplex
mode and auto MDI/MDI-X connection
Combo Ports (RJ45/SFP)
2 x 10/100/1000BaseT(X) or 100/1000BaseSFP
RS232 Console Port
RS232 Interface with RJ45 connector for Console access
LED Indicators
PWR1, PWR2 (Power), Fault (Relay), Ring Master, Ring
Status, Port Link/Activity/Speed, Port Full/Half Duplex
Mode
Relay Contact
Max. 1A @ 24 V DC
Power supply
Input Voltage
24 V DC (12 - 48 V DC), 2 redundant inputs
Input Current
1.2 A @ 12 V DC
0.6 A @ 24 V DC
0.3 A @ 48 V DC
Connection
One removable 6-pin terminal block, Wiring cable 12-
24AWG
Overload Current Protection
Present
Reverse Polarity Protection
Present
Physical Characteristics
Housing
IP30 protection, metal
Dimension (W x H x D)
96.4 x 154 x 108.5 mm (3.8 x 6.06 x 4.27 inch)
Weight
1281 g
Installation
DIN-rail
Environmental conditions
Operating Temperature
-40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Operating Altitude
Up to 2000 m
Regulatory Approvals
Safety
EN 62368-1; UL 61010-1; UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A,
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 0.5 kV; Signal: 0.5 kV,
IEC 61000-4-5 Surge: Power: 0.5 kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 Vrms
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-31
Vibration
IEC 60068-2-6
MTBF
Time
600.504 hrs
Database
Telcordia SR332
Warranty
Time Period
5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone +49 (0) 5231 14-0, Fax +49 (0) 5231 14-292083
E-Mail [email protected], Internet www.weidmueller.com
