4
5
6 V1.2 / 2022-03-29
Refer to illustration below for correct wiring.
Behavior of fault alarm relay (can be triggered by configurable events power failure or
port link down):
Relay contact is closed if the device is powered-off.
Relay contact is open if the device is powered-on and no alarm conditions exist (neither
Power Failure Alarms nor Port Link Loss Alarms are activated (Web menu Warnings
Fault Relay Alarm).
Relay contact closes if any of an activated alarm condition happens.
9. Communication Connections
Switch
IE-SW-AL06M-4GTPoE-2GESFP
is equipped with the following communication
interfaces:
4 x 10/100/1000BASE-T(X) PoE ports (P.S.E.)
2 x 100/1000BASE-X Ports (SFP Slots)
9.1
10/100/1000BASE-T(X) PoE ports (P.S.E)
For communication without PoE sourcing the switch supports auto negotiation speed,
Full/Half duplex mode and auto MDI/MDI-X connection, means automatic setting of pinouts
for both MDI ports (NIC-type) or MDI-X ports (HUB/Switch-type).
In case of active PoE sourcing the switch uses the pinout of “
Alternative A, MDI mode
” of
802.3af/802.3at standards. Please see the details in the following table.
Pinouts
10/100/1000BASE-T(X) PoE ports (P.S.E)
8-Pin RJ45
Port
10/100 BASE-T(X) MDI/MDI-X
1000BASE-T MDI/MDI-X
Pin
No.
MDI port
MDI-X port
Pin
No.
MDI port
MDI-X port
1
TD+(transmit) with
PoE Power +
RD+(receive)
1
BI_DA+ with
PoE Power +
BI_DB+
2
TD-(transmit) with
PoE Power +
RD-(receive)
2
BI_DA- with
PoE Power +
BI_DB-
3
RD+(receive) with
PoE Power -
TD+(transmit)
3
BI_DB+ with
PoE Power -
BI_DA+
4
Not used
Not used
4
BI_DC+
BI_DD+
5
Not used
Not used
5
BI_DC-
BI_DD-
6
RD-(receive) with
PoE Power -
TD-(transmit)
6
BI_DB- with
PoE Power -
BI_DA-
7
Not used
Not used
7
BI_DD+
BI_DC+
8
Not used
Not used
8
BI_DD-
BI_DC-
9.2
100/1000BASE-X SFP fiber optic port
The 100/1000BASE SFP type slots require either a 100BASE SFP or a 1000BASE SFP fiber
transceiver (mini-GBIC) to work properly. Please only use SFP modules and cables that are
compatible with each other to establish an optical connection.
LC-Port Pinouts:
LC-Port to LC-Port Cable Wiring:
For a LC-Port with separate Transmit and Receive Port please remember to connect the Tx
(transmit) port of Device-1 to the Rx (receive) port of Device-2, and the Rx (receive) port of
Device-1 to the Tx (transmit) port of Device-2.
9.3
RS232 Console Port
The RS232 Interface with RJ45 connector can be used to access the switch console for
configuration. Additionally, it can be applied with external Backup/Restore module IE-EBR-
MODULE-RS232-ALM (Article no. 2682610000).
Pinouts Serial
Console Port:
10. User Management
10.1 Device Access (Login to Web Interface)
The Web interface of the Switch can be accessed via following factory default settings:
IP address / Netmask:
192.168.1.110 / 255.255.255.0
User name:
admin
Password:
Detmold
Connect the PC to any Ethernet port of the managed Switch and set the PC’s IP address to a
free one of range 192.168.1.0 / 255.255.255.0
Start a web browser and enter the IP address of the connected Switch into the browser’s
address line (http://192.168.1.110). After the appearance of prompt (login) enter the login
credentials. After confirmation of your input with "OK" the home page of the switch will be
displayed.
10.2 Reset Button (Behavior of Factory Default Settings)
Pressing < 5 seconds: Reboot the switch (Warm Start) and sets IP to
Factory Default IP.
Pressing >= 5 seconds: Resets the switch configuration to Factory Default Settings.
Note: Behavior of reset button can be configured in the Web Interface (Menu Factory Default).
11. LED Indicators
The front panel of the Ethernet Switch contains several LED indicators. The function of each
LED is described in the table below.
LED
Color
Status
Description
PWR1
Green
On
Power is supplied to power input PWR1.
PWR2
Green
On
Power is supplied to power input PWR2.
R-MSTR
(Ring Master)
Green
On
Is Ring Master of an enabled O-Ring.
Ring
Green
On
O-Ring redundancy is enabled.
Blinking
Ring structure is broken (No redundancy).
PoE
Green
On
Power supplied over Ethernet
LNK/ACT
(Ports G1-G4)
Green
On
Port link is active.
Off
Port link is inactive.
Blinking
Data is transmitted.
10/100/1000M
(Ports G1-G4)
Green /
Amber
Green
Port speed is set to 1000 Mbps.
Amber
Port speed is set to 100 Mbps.
Off
Port speed is set to 10 Mbps.
LNK/ACT
(SFP Ports
G5-G6)
Green
On
Port link is active.
OFF
Port link is inactive.
Blinking
Data is transmitted.
FAULT
Amber
On
Fault Relay indication for Power failure and Port link loss.
12. Disposal Information
Observe the notes for proper disposal of the
product. You can find the notes here:
www.weidmueller.com/disposal
.
13. Specifications
Technology
Ethernet Standards
IEEE 802.3 for 10BASE-T
IEEE 802.3u for 100BASE-TX and 100BASE-FX
IEEE 802.3ab for 1000BASE-T
IEEE 802.3z for 1000BaseX
IEEE 802.3x for flow control
IEEE 802.3af/at for Power over Ethernet
IEEE 802.3ad for port trunk with LACP
IEEE 802.1D for STP (Spanning Tree protocol)
IEEE 802.1w for RSTP (Rapid Spanning Tree protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1p for Class of Service
IEEE 802.1Q for VLAN Tagging
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
Processing Type
Store and Forward
MAC Table size
8K
Packet buffer size
4 Mbit
Backplane bandwidth
12 Gbps
Jumbo frame support
Up to 9.6 kBytes
Interfaces
RJ45 Ports
10/100/1000BASE-T(X) PoE ports (P.S.E.) compliant to PoE
standard IEEE 802.3af/at
Fiber optic ports
2 x 100/1000BASE-X SFP slots
RS232 Console Port
RS232 Interface with RJ45 connector for Console access and
useable with external Backup/Restore module
LED Indicators
PWR1, PWR2 (Power), Fault (Relay), Ring Master, Ring
Status, Port Link/Activity/Speed, PoE
Relay Contact
Max. 1A @ 24 V DC for Power Failure and Port Link Loss
Power
Input Voltage
12/24/48 V DC (12 - 57 V DC), 2 redundant inputs
Input Current
(with PD consumption)
6.6 A @ 12 V DC; 5.68 A @ 24 V DC; 2.76 A @ 48 V DC
Connection
One removable 6-pin terminal block, Wiring cable 12-24AWG
Overload Current Protect.
Present
Reverse Polarity Protect.
Present
PoE
Total power budget
60 W @ 12 – <24 V DC; 120 W @ 24 - 57 V DC
PoE Pinout
Mode A: Pin 1, 2 (V+); Pin 3, 6 (V-); Alternative A; MDI
Physical Characteristics
Housing
IP30 protection, metal
Dimension (W x H x D)
54.3 x 145.1 x 108.5 mm (2.14 x 5.71 x 4.27 inch)
Weight
678 g
Installation
DIN-rail
Environmental conditions
Operating Temperature
-40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Operating Altitude
Up to 2000 m
Regulatory Approvals
Safety
UL 61010-1; UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A,
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 0.5 kV; Signal: 0.5 kV,
IEC 61000-4-5 Surge: Power: 0.5 kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 V
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-31
Vibration
IEC 60068-2-6
MTBF
Time
495.624 hrs
Database
Telcordia SR332
Warranty
Time Period
5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone +49 (0) 5231 14-0, Fax +49 (0) 5231 14-292083
, Internet
www.weidmueller.com
