background image

3

    WARNING:

 To reduce the risk of serious injury, read all important precautions and 

instructions in this manual and all warnings on the weight bench before using the weight bench. 

Sears assumes no responsibility for personal injury or property damage sustained by or through the 

use of this product.

1.  It is the responsibility of the owner to ensure 

that all users of the weight bench are ade-

quately informed of all precautions.

2.  Before beginning any exercise program, 

consult your physician. This is especially 

important for persons over age 35 or per-

sons with pre-existing health problems.

3.  The weight bench is not intended for use by 

persons with reduced physical, sensory, or 

mental capabilities or lack of experience and 

knowledge, unless they are given supervi-

sion or instruction about use of the weight 

bench by someone responsible for their 

safety.

4.  Use the weight bench only as described in 

this manual. 

5.  The weight bench is intended for home use 

only. Do not use the weight bench in any 

commercial, rental, or institutional setting.

6.  Keep the weight bench indoors, away from 

moisture and dust. Do not put the weight 

bench in a garage or covered patio, or near 

water.

7.  Place the weight bench on a level surface, 

with enough clearance around the weight 

bench to mount, dismount, and use the 

weight bench. To protect the floor or carpet 

from damage, place a mat under the weight 

bench.

8.  Inspect and properly tighten all parts each 

time the weight bench is used. Replace any 

worn parts immediately.

9.  Keep children under age 13 and pets away 

from the weight bench at all times.

10. Keep hands and feet away from moving 

parts.

11. Always wear athletic shoes for foot 

protection while using the weight bench.

12. The weight bench is designed to support a 

maximum user weight of 250 lbs. (113 kg), 

and a maximum total weight of 360 lbs. (163 

kg). Do not place more than 110 lbs. (49 

kg), including a barbell and weights, on the 

weight rests. Do not place more than 50 lbs. 

(23 kg) on the leg lever. 

13. Do not use a barbell that is longer than five 

ft. (1.5 m) with the weight bench.

14. Always place the same amount of weight 

on both ends of the barbell. While adding or 

removing weights, always keep some weight 

on both ends of the barbell to prevent the 

barbell from tipping. Always secure weights 

with the spring collars.

15. Before using the leg lever, place the bar-

bell with the same amount of weight on the 

weight rests to balance the bench.   

16. Before using the backrest, make sure that 

the backrest support is inserted fully into the 

uprights.

17. Always exercise with a partner. Your partner 

should be ready to catch the barbell if you 

cannot complete a repetition 

18. Over exercising may result in serious injury 

or death. If you feel faint, if you become short 

of breath, or if you experience pain while 

exercising, stop immediately and cool down.

IMPORTANT PRECAUTIONS

Summary of Contents for 265 831.15963.0

















Reviews: