manualshive.com logo in svg

WEG PLC300, User Manual, Page: 58 / 76

Share
Download
WEG PLC300 User Manual Download Page 58

Alarms

10-2 | PLC300

IMPORTANT

: Information can be lost in case the PLC300 is turned off and the battery 

voltage is below 1.9 V.

Automatic Software Recovery (ASR)

 - Indicates the user’s software was considered 

invalid and was recovered from the SD card.

Watchdog Tasks 

– when Watchdog is detected in any task of the user, the program 

stops and an alarm occurs, indicating which task generated Watchdog. Simultaneously 

the Reading System Marker corresponding to the task is set (System Markers %SB0050 

to %SB0055). The configuration of the Watchdog of the tasks is executed by means of 

the WPS.

Nonexistent or Invalid SD Card 

 – error in the attempt to write or read the SD Card 

through the Event Log, Alarm Log or Recipes.

10.2 USER ALARMS

They are the alarms programmed by the user, using the WPS. They are activated by a bit marker. 

Programming of the User Alarms

The user alarms must be configured by the WPS programming software. The user enters 

the bit marker that will activate the alarm; it indicates if the actuation will be in the low or 

high level of the bit and the texts of the alarm.

Other common data to all these alarms are also set by the WPS, such as: maximum number 

of alarms and size of the alarm history. 

These data affect the available memory, so they must be optimized for the user needs.

It is possible to show the content of a variable, formatted, in the second line of the alarm.

10.3 ALARM SCREENS

The PLC300 has two internal screens that help in the verification of the alarms, both internal 

and the user’s. The List of Active Alarms and the Alarm History.

List of Active Alarms

By pressing the <ALARM> key, the alarm is acknowledged, making the LED stop flashing. 

The screen of active alarms is open, showing at the top, the last active alarm.

For instance:

A C T I V E   A L A R M S

> 0 0 2 : A c t u a t o r 1 F a i l

0 0 1 : O v e r t e m p . K 1

In this example, the alarm “

Actuator1 Fault

” was the last to happen, seeing that there 

is still another active alarm. “

Overtemp. K1

”.

Summary of Contents for PLC300













































































Reviews:

No comments