Weed Eater 545117552 Instruction Manual Download Page 11

11

TROUBLE

CAUSE

REMEDY

Engine will not

start or will run

only a few

seconds after

starting.

1.ON/OFF switch in OFF

position.

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching

carburetor.

6.Compression low.

1. Move ON/OFF switch to the ON

position.

2. See “Difficult Starting” in

Operation Section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

5. Contact an authorized service dealer.

Engine will

not idle

properly.

1. Carburetor requires

adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. See “Carburetor Adjustment” in

Service and Adjustments Section.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer.

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires

adjustment.

4. Carbon build up.

5. Compression low.

Engine will not

accelerate,

lacks power,

or dies under

a load.

1. Clean or replace air filter.

2. Clean or replace plug

and regap.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

Engine

smokes

excessively.

1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.

4. Carburetor requires

adjustment.

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.

4. Contact an authorized service dealer.

Engine runs

hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build-up.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

WARNING:

Always stop unit and disconnect spark plug before performing all of the

recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

Blade turns at

idle speed.

1. Carburetor requires

adjustment.

2. Throttle cable binding.

3. Clutch requires repair.

1. See “Carburetor Adjustment” in

Service and Adjustments Section.

2. Replace or repair throttle cable.

3. Contact an authorized service dealer.

Blade stops un-

der a load or

does not turn

when engine is

accelerated.

1. Blade not engaged.

2. Carburetor requires

adjustment.

3. Clutch requires repair.

1. Check gearbox.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer.

Summary of Contents for 545117552














Reviews: