3
S
Do not abuse cord. Never carry the unit by
the extension cord or yank extension cord
to disconnect unit.
S
Use cord retainer to prevent disconnection
of extension cord from unit and possible
damage to the unit due to plug movement
(see ATTACH THE EXTENSION CORD
TO YOUR TRIMMER in the OPERATION
section).
S
Do not use the unit if the switch does not
turn the unit on and off properly. Repairs to
the switch must be made by your autho-
rized service dealer
.
S
Keep the extension cord clear of operator
and obstacles at all times. Do not expose
cords to heat, oil, water, or sharp edges.
S
To avoid the possibility of electric shock,
avoid body contact with any grounded con-
ductor, such as metal fences or pipes.
S
Ground Fault Circuit Interrupter (GFCI)
protection should be provided on circuit or
outlet to be used. Receptacles are avail-
able having built-in GFCI protection and
may be used for this measure of safety.
UNIT SAFETY
S
Inspect unit before use. Replace damaged
parts. Make sure all handles, guards, and
fasteners are in place and securely fas-
tened. Parts that are damaged must be re-
paired or replaced by an authorized service
dealer
.
These include head parts that are
cracked, or chipped, guards, and any other
part that is damaged.
S
Do not repair unit yourself.
S
Use only 0.065 inch (1.65 mm) diameter
recommended trimmer line (see USER
REPLACEABLE SERVICE PARTS in the
SERVICE AND ADJUSTMENTS section).
Never use wire, rope, string, etc.
S
Use specified trimmer spool. Make sure
spool is properly installed and all parts are
securely fastened.
S
Use only WEED EATER replacement parts
and accessories as recommended.
CUTTING SAFETY
S
Inspect area to be cut. Remove objects
(rocks, broken glass, nails, wire, string,
etc.) which can be thrown or become en-
tangled in cutting head.
S
Do not overreach or stand on unstable sup-
port. Keep firm footing and balance.
S
Keep the cutting head below waist level. Do
not raise handles above your waist. Cutting
head can come dangerously close to your
body.
S
Keep away from cutting head and spinning
line.
S
Use unit properly. Use only for trimming,
edging, scalping, and mowing. Do not
force unit. It will do the job better and with
less risk of injury at the rate for which it was
designed.
S
Use only in daylight or in good artificial light.
MAINTENANCE SAFETY
WARNING:
Disconnect unit from the
power supply before performing mainte-
nance, or when changing trimmer line.
S
Maintain unit according to recommended
procedures. Keep cutting line at proper
length. Follow instructions for changing
trimmer line.
S
Have all service and maintenance not ex-
plained in this manual performed by an au-
thorized service dealer to avoid creating a
hazard.
S
Never douse or squirt the unit with water or
any other liquid. Clean unit and decals with
a damp sponge. Keep handles dry, clean,
and free from oil and grease.
S
Keep the air vents clean and free of debris
to avoid overheating the motor. Clean after
each use.
TRANSPORTING AND STORAGE
S
Stop the unit and disconnect the power
source when not in use.
S
Carry the unit with motor stopped.
S
Store the unit so the line limiter blade (on
underside of shield) cannot cause injury.
S
Store unit indoors in a high, dry place out of
the reach of children. Store unit unplugged.
S
Do not hang unit so that the trigger switch is
depressed.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help protect
against electric shock. Double insulation
construction consists of two separate “layers”
of electrical insulation instead of grounding.
Tools built with this insulation system are not
intended to be grounded. No grounding
means is provided on this unit, nor should a
means of grounding be added to this unit. As a
result, the extension cord used with your unit
can be plugged into any standard 120 volt
electrical outlet.
Safety precautions must be observed when
operating any electrical tool. The double in-
sulation system only provides added protec-
tion against injury resulting from an internal
electrical insulation failure.
WARNING:
All electrical repairs to
this unit, including housing, switch, motor,
etc., must be diagnosed and repaired by qual-
ified service personnel. Replacement parts
for a double insulated appliance must be rec-
ommended by the manufacturer. A double in-
sulated appliance is marked with the words
“double insulation” or “double insulated”. The
symbol (square within a square)
may also
be marked on the appliance. Failure to have
the unit repaired by qualified service person-
nel can cause the double insulation construc-
tion to become ineffective and result in seri-
ous injury.
SAVE THESE INSTRUCTIONS
