Weed Eater 530163351 Instruction Manual Download Page 11

11

Cut using the 2

o’clock to 4 o’clock

position of the

blade

2 o’clock

4 o’clock

RECOMMENDED CUTTING POSITION

WARNING:

The operator or others

must not try to clear away cut material with the

engine running or the blade turning to avoid

serious injury. Stop engine and blade before

removing materials wrapped around blade or

tube.

MAINTENANCE

WARNING:

Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

CHECK FOR LOOSE

FASTENERS AND PARTS

S

Spark Plug Boot

S

Air Filter

S

Housing Screws

S

Assist Handle Screw

S

Debris Shield

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

S

ON/OFF Switch -- Ensure ON/OFF switch

functions properly by moving the switch to

the OFF position. Make sure engine stops;

then restart engine and continue.

S

Fuel Tank -- Discontinue use of unit if fuel

tank shows signs of damage or leaks.

S

Debris Shield -- Discontinue use of unit if

debris shield is damaged.

INSPECT AND CLEAN UNIT AND DE-

CALS

S

After each use, inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

S

Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after every

5 hours of operation.

1. Clean the cover and the area around it to

keep dirt from falling into the carburetor

chamber when the cover is removed.

2. Remove parts as illustrated.

NOTE:

To avoid creating a fire hazard or

producing harmful evaporative emissions, do

not clean filter in gasoline or other flammable

solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Add a few drops of oil to the filter;

squeeze the filter to distribute oil.

6. Replace parts.

Air filter cover

Screws

Air filter

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

WARNING:

The muffler on this prod-

uct contains chemicals known to the State of

California to cause cancer.

WARNING:

Muffler is very hot during

and after use. Do not touch the muffler or al-

low combustible material such as dry grass or

fuel to do so.

As your unit is used, carbon deposits build up

on the muffler and spark arresting screen.

For normal homeowner use, however, the

muffler and spark arresting screen will not re-

quire any service.

After 50 hours of use, we recommend that

your muffler be serviced or replaced by your

authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure

the engine starts easier and runs better. Set

spark plug gap at 0.025 inch. Ignition timing is

fixed and nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and

discard.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 in.

socket wrench.

4. Reinstall the spark plug boot.

Summary of Contents for 530163351
















Reviews: