3
S
Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S
Stop engine and allow to cool before re-
moving fuel cap.
S
Always store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAFETY
WARNING:
Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S
Use only for trimming, mowing, and sweep-
ing. Do not use for edging, pruning or hedge
trimming.
S
Keep firm footing and balance. Do not over-
reach.
S
Keep all parts of your body away from muf-
fler and spinning line. Keep engine below
waist level. A hot muffler can cause serious
burns.
S
Cutting on left side of the shield will throw
debris away from the operator.
S
Use only in daylight or good artificial light.
TRANSPORTING AND STORAGE
S
Allow the engine to cool; secure unit before
storing or transporting in vehicle.
S
Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbu-
retor by starting engine and letting it run un-
til it stops.
S
Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S
Store unit so line limiter blade cannot acci-
dentally cause injury. Unit can be hung by
the tube.
S
Store the unit out of the reach of children
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, call
1-800-554-6723
.
SAFETY NOTICE:
Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings.
Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE:
This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by your Au-
thorized Service Dealer.
ASSEMBLY
WARNING:
Make sure unit is proper-
ly assembled and all fasteners are secure.
ADJUST THE HANDLE
S
Loosen wing nut or plastic knob on handle.
S
Rotate handle to upright position and tight-
en in a comfortable position between the
trigger and the safety label on the tube.
Tighten handle securely.
ATTACHING THE SHIELD
WARNING:
The shield must be prop-
erly installed. The shield provides partial
protection from the risk of thrown objects to
the operator and others and is equipped with
a line limiter blade which cuts excess line. The
line limiter blade (on underside of shield) is
sharp and can cut you.
S
Remove wing nut from shield.
S
Insert bracket into slot as shown.
S
Pivot shield until bolt passes through hole in
bracket.
S
Securely tighten wing nut onto bolt.
Bracket
Shield
Slot
FUELING
This engine is certified to operate on un-
leaded gasoline. Gasoline must be mixed
with a good quality 2-cycle air-cooled engine
oil designed to be mixed at a ratio of 40:1.
Poulan/Weed Eater brand oil is recom-
mended. (A 40:1 ratio is obtained by mixing
3.2 ounces of oil with 1 gallon of unleaded
gasoline). When mixing fuel follow the
instructions printed on the container. Always
read and follow the safety rules under
FUEL
SAFETY.
