manualshive.com logo in svg

Weco HeSU 4K4-R19/4, Product Manual, Page: 14 / 56

Share
Download
Weco HeSU 4K4-R19/4 Product Manual Download Page 14

WeCo - HeSU 4K4 Low Voltage UNIVERSAL STACKABLE MODEL 

 
 
 
 
 

HeSU 4k4 UNIVERSAL STACKABLE * HIGH CURRENT                      V_1.07.1_2019    P

age-14

 

 
 

5.3.2 Installation/Assembly Method 

 

5.3.2.1 Installation of accessories and preparatory phases 

Phase 1: Choose the support surface carefully, the batteries have a weight of over 50 kg each and can reach 270 kg 

including the accessories, in a stack of five batteries. 

The surface profile of the battery on the ground is 55cm x 46cm but the actual contact with the ground is made by 4 

supports of about 4x10 cm each. 

Make sure the support surface is adequate to support the overall battery load. 

 

 

Information

：

 

Preparation of the modules 

The battery is delivered as standard in a 

WALL MOUNT CONFIGURATION

 and it is therefore necessary that the installer 

make simple external changes to install the 

STACK KIT.

   

 

 

 

STACK MOUNT INSTALLATION PHASES FOLLOW 

 

1.

 

Install the support feet on the back of the battery using the supplied screws. Each foot must be   

installed with 2 M8 Allen screws supplied. Repeat the operation for all the batteries you want to stack.

   

 

   

 

 

Summary of Contents for HeSU 4K4-R19/4

























































Reviews:

No comments