clamp in the plug making sure that it grips the outer covering of the cord. In a 13A
(BS 1363) fused plug, fit a 13A fuse. Tighten the plug cover securely.
If you are in any doubt, consult a qualified electrician.
IMPORTANT: The supply cord on this appliance is of a special type. If replaced,
only a Burco supply cord must be used. The supply cord may become warm when the
appliance is in use.
Features
1
Removable lid (Easy access for descaling)
2
Removable front cover
3
On/Off switch
4
Safety locking tap
5
Hose for connection to drinking water
Preparation
1
Remove any plastic film from the water boiler and wipe over all surfaces with a
clean cloth.
2
Check that the voltage on the rating plate of your appliance corresponds with
your electricity supply which must be A.C. (Alternating Current).
3
Before using it is recommended that the water boiler is boiled twice, discarding
the water each time.
Check list
Before starting installation check that you have the following parts:
•
Autofill water boiler
•
Drip tray
•
Food safe hose
Connecting to a water supply
Your water boiler has been supplied with a suitable hose
5
for connection to a
drinking water supply. The water supply must have a pressure not exceeding 1000
kilopascals (10 bar) and no lower than 25 kilopascals (0.25 bar). If your water pressure
exceeds this, a suitable pressure reduction value will need to be fitted.
Please ensure that you follow the bye-laws of the water council when installing
this product.
Burco cannot be held responsible for water boiler malfunction if the water supply
pressure does not confirm as above. If in any doubt consult your water supply
company.
The hose supplied with the water boiler is manufactured from materials which
have been approved for drinking water and is rated at 10 bar at ambient temperature.
It is therefore recommended that the water boiler is only connected to a cold water
supply. Your guarantee could be invalidated and water contamination may occur if a
hose not supplied by Burco is used. Please note that washing machine hoses are not
suitable for use on this water boiler.
Connection to mains water supply
Your autofill water boiler can be set up so that the mains water connection can
either enter your water boiler at the back or the bottom of the unit.
To set up connection from back of unit:
•
Using a screw driver remove blanking plate from back of unit
A
.
•
Attach supplied water connection fitting to water inlet (screw fitting) and when
secure attach the pipe
B
.
•
Tightly attach other end of water connection hose to mains water supply.
•
Ensure all pipes are suitably insulated to prevent water supply from freezing.
•
If rear overflow is required see instructions below on how to set this up at this
point.
To set up connection from bottom of unit:
•
Using a screw driver remove blanking plate from back of unit
A
.
•
Attach supplied water connection hose to water inlet with the elbow joint
connection on the hose (screw fitting)
C
.
•
Tightly attach other end of water connection hose to mains water supply.
•
Replace blanking plate.
Overflow
Connecting rear overflow
An air gap of 200mm from the connection point must be provided. Failure to
provide this air gap will cause an air lock and stop the water discharging in event of
an overflow.
IMPORTANT: For rear overflow connection a 14mm internal diameter hose or a
15mm internal diameter hose with a pipe clip must be used. While every reasonable
precaution is taken to prevent an overflow, Burco cannot be held responsible for any
damage caused as a result of incorrect installation or blockage of the overflow.
•
Attach a suitable 14mm internal diameter or 15mm internal diameter hose with
a pipe clip, to outlet connection. (Hose not supplied)
•
Attach other end of outlet hose to mains drain.
If connection to the bottom of the water boiler is desired now replace the
blanking place at the back of the unit, using screw driver to tighten in place.
4
5