Weber Genesis 1300 Owner'S Manual Download

Page: 1 / 36

Serial Number

Please use this number in registering your warranty and
any correspondence with the factory.

Owner’s Manual

National

Association

PROPANEGAS

92725

11/98

GENESIS

1300 Series

LP Gas Barbecue



WARNING

1. Do not store spare LP Cylinder within

10 feet (3m) of this appliance.

2. Do not store or use gasoline or other

flammable liquids or vapors within 25
feet (8m) of this appliance.



DANGER

If you smell gas:

1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, Keep away from the

appliance and immediately call your
gas supplier or your fire department.

Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death or damage to property.

NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.

WARNING: Follow all leak check procedures
carefully in this manual prior to barbecue
operation. Do this even if barbecue was
dealer assembled.

WARNING: Do not try to light this appliance
without reading "Lighting" instructions
section of this manual.

THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.

Summary of Contents for Genesis 1300





































Search results

Summary of Contents for Genesis 1300

Reviews:

Related manuals for Genesis 1300

Brands by name

Popular brands

Weber Genesis 1300, Owner'S Manual

Search results

Summary of Contents for Genesis 1300

Reviews:

Related manuals for Genesis 1300

Brands by name

Popular brands