Webasto U4814 Service Information Download Page 2

Service Information

Rev. 0

8

/20

21

 • 907634

Webasto Product North America, Inc. 

North American Headquarters

• 15083 North Road • Fenton, Michigan 48430

For Technical Assistance Call:

(800) 555-4518 • 

In Canada Call:

(800) 667-8900

Visit us on the Web at:

www.webasto.us (North America) www.webasto.com (Global)

Seal Kit Assembly Instructions for Coolant Pumps:

 

U4814, U4816, U4817 and U4851

*

Page 2 of 2

Assembly (See Figure 3)

ATTENTION!

Do not damage the motor shaft’s surface during the following
procedures.  Prevent liquid solvents from penetrating into the
motor bearing.

1. Remove dirt and deposits from the motor shaft.

NOTE:

On circulation pump U4814, check screws on the bearing end
plate for a tight fit and tighten to 2 Nm. (17.7 lb-in.)

2. Slide the splash guard (item 11) and the washer (item 10)

to the limit stop on the motor shaft.

3. Cut the top of the lubricating oil bottle open.  Cover the

motor shaft completely with a film of lubricating oil,
while the shaft is in a horizontal position, as shown in
figure 3.

NOTE:

Cover the motor shaft completely with lubricating oil in order
to ensure a correct assembly (self-adjustment) of the sliding
unit and to prevent leakage.

ATTENTION!

The lubricating film on the sealing surface of the base axial
seal should not be damaged or removed.
Avoid impurities on the sealing surface!

4. Remove pump base (item 9) with integrated axial seal

(item 12) from its individual packaging.

5. Slip pump base (item 9) onto the motor shaft towards

splash guard (item 11) and align it with the mounting
holes on the motor flange.

6. Attach the pump base with screws (item 7) and spring

washers (item 8) and tighten screws to 4 Nm. (35.4 lb-in.).

7. Remove sliding seal unit (item 5) from protective cover

(item 13).

8. Align sliding unit (item 5) with motor shaft (flat regions)

and slide it onto the shaft until it touches the limit stop.

9. Slide pump impeller (item 4) onto the motor shaft (sliding

seal is self adjusting).

10. Install nut (item 3), adjust pump impeller (item 4) and

tighten the nut to 1.5 Nm (13.2 lb-in.).

11. Install O-ring seal (item 6) on pump base (item 9) twist-free

over the edge.

12. Place pump cover (item 2) over pump base (item 9), fasten

with screws (item 1) and tighten screws to 2 Nm.

13. Punch out the dates of initial operation (month/year) on

the “Webasto-replacement part” label and attach the label
to the motor body, as shown in figure 1 on previous page.

14. Install the circulation pump in the vehicle.
15. Check for smooth operation without leakage.

ATTENTION!

If the replacement part label is not attached or the dates on
the label are not punched out, the warranty is void.  Do not
paste anything over old labels, should parts be replaced several
times during the motor’s service life.

Legend for Figure 3

1 Screw (4)
2 Pump cover
3 Nut
4 Pump impeller
5 Sliding unit
6 O-ring seal
7 Screw (4)
8 Spring washer (4)
9 Pump base

10 Washer
11 Splash guard
12 Integrated axial seal
13 Protective container

for sliding seal with
manufacturing date

14 Bottle of lubricating oil

Figure 3:  Assembly

Motor Shaft

NOTE: U 4851 Pump has been superseded to U 4855 Pump.

Reviews: