background image

WIRELESS CONNECTIVITY & SENSORS

ANR022 - Radio module cross migration guide

Pin

No.

Thyone-I

sub-GHz proprietary

module

Description

22

Not

connected

RESERVED

on sub-GHz

proprietary module

ANT-CTRL

on Adapter

board

ANT-CTRL

Pin 22

of the adapter

board controls RF switch to change
between antenna

23

GND

GND

Ground

i1

SWDIO

TEST

Debug Interface

i2

SWDCLK

TEST

Debug Interface

i3

Not

connected

TEST

i4

Not

connected

TEST

Table 3: Pin mapping between Thyone-I and

sub-GHz proprietary module

4.1.3 Antenna

Using the adapter board along with Thyone-I module, the option to switch between internal and
external antenna connection is available. The

ANT

pin (No.1, Ext_ANT in the schematic) of

the adapter board is used for an external antenna connection matched to 50

.

The

ANT-CTRL

pin (No.22) is used to switch between Thyone-I on-board PCB antenna and

the external antenna pin

Ext_ANT

of the adapter board.

The

ANT-CTRL

pin (No.22) has an internal pull-down resistor and selects in-

ternal PCB antenna by default. An external pull-up resistor on this pin shall be
avoided.

By applying a high logic level to the

ANT-CTRL

pin, the

ANT

Pin of the adapter board can

be used for external antenna connection. If

Pin 22

is left open or a low level is applied, the

Thyone-I on-board PCB antenna is used.

4.1.4 Trace design

Thyone-I Module itself complies with FCC and IC certification. For evaluation purpose, the
adapter board uses an IC to switch between the on-board PCB-antenna of the Thyone-I mod-
ule and the external RF PAD connection. Due to which the adapter board differs from the trace
design and is not approved to be FCC and IC compliant.

14

Version 1.1, July 2023

www.we-online.com/wcs

Summary of Contents for TARVOS-III




























Reviews: