background image

 

ii

 

 

 

 

 

 

 

 

Operational Safety Notices

 

The radio equipment described in this guide emits radio frequency 
energy. Although the power level is low, the concentrated energy from 
a directional antenna may pose a health hazard. When using a gain 
antenna of 8 dBi (350-512 MHz) or 12 dBi (800-960 MHz), do not allow 
people to come closer than 0.5 meters to the front of the antenna when 
the transmitter is operating. Using higher gain antennas would mean 
increasing this distance accordingly.

This manual is intended to guide a professional installer to install, 
operate and perform basic system maintenance on the described radio.

 

ISO 9001 Registration

 

Wireless Data Systems' adheres to this internationally accepted quality system
standard.

 

WDS Quality Policy Statement

 

We, the employees of Wireless Data Systems, are committed to 
achieving total customer satisfaction in everything we do.

 

Total Customer Satisfaction in:

 

• Conception, design, manufacture and marketing of our products.

• Services and support we provide to our internal and external cus-

tomers.

 

Total Customer Satisfaction Achieved Through:

 

• Processes that are well documented and minimize variations.

• Partnering with suppliers who are committed to providing quality 

and service.

• Measuring our performance against customer expectations and 

industry leaders.

• Commitment to continuous improvement and employee involve-

ment.

 

Notice

 

While every reasonable effort has been made to ensure the accuracy of 
this manual, product improvements may result in minor differences 
between the manual and the product shipped to you. If you have addi-
tional questions or need an exact specification for a product, please con-
tact our Customer Service Team using the information at the back of this 
guide. In addition, manual updates can often be found on the WDS web 
site at 

 

www.sinosun.cn.

 

.

RF Exposure

Summary of Contents for P20

































Reviews: