background image

Safety Glasses

Phillips Head 

Screwdriver

Step Ladder

Ratchet Wrench

7/16” Wrench

5/64” Drill Bit

3/16” Drill Bit

1/8” Drill Bit

7/16” Socket

Flat Tip 

Screwdriver

Needle Nose Pliers

Level

7/16” Socket Driver

Pliers/Wire 

Cutters

3/32” Drill Bit

Tape Measure

Pencil

Power Drill

 

CAUTION

 TO REDUCE THE RISK OF INJURY, USE THIS OPENER ONLY WITH THE FOLLOWING DOOR MODELS:

System Requirements

Locking Pliers

WAYNE-DALTON

DOOR MODEL

WAYNE-DALTON 

SPRING SYSTEM

TRACK (RADIUS)

PHOTOELECTRIC 

SAFETY SENSORS

LOW HEAD

ROOM KIT

9000 SERIES

Torquemaster

®

Torquemaster

®

 Plus

10",12",14",15"

Not Required

Not Required

9000 SERIES

Torquemaster

®

Torquemaster

®

 Plus

6" Low Head Room

Not Required

P/N 302883 

Required

8000 SERIES

Torquemaster

®

Torquemaster

®

 Plus

10",12",14",15"

P/N’s 252118 or

301674 Required

Not Required

8000 SERIES

Torquemaster

®

Torquemaster

®

 Plus

6" Low Head Room

P/N’s 252118 or

301674 Required

P/N 302883 

Required

IV

Please Do Not Return This Product To The Store. 

Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 

1-888-827-3667

 for Consumer Assistance or online at 

www.wayne-dalton.com

Vice Clamps

Tools Needed

Summary of Contents for idrive pro 3790









Reviews: