12” to 18” apart.
FOR FULLY ADJUSTABLE TRACK:
For the header, align the weatherstrip 1/8” to 1/4” inside
the header edge, and temporarily secure it to the header with equally spaced nails. Starting
at either side of the jamb, fit the weatherstrip up tight against the temporarily attached
weatherstrip in the header and 1/8” to 1/4” inside the jamb edge. Temporarily secure the
weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom sec-
tion from falling out of the opening during installation. Equally space nails approximately 12”
to 18” apart.
HEADROOM REQUIREMENT:
Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2” (64 mm) of additional headroom is required.
NOTE:
6” low headroom conversion kit is available for 12” radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT:
Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
*NOTE:
For door heights from 10’1” to 14’0”, refer to your operator manufacture installation
instructions for appropriate depth into room.
BACKROOM REQUIREMENTS
Door Height
Track
Manual Lift
Motor Operated
6’0” to 7’0”
12”, 15” Radius
102” (2591 mm)
125” (3175 mm)
7’1” to 8’0”
12”, 15” Radius
114” (2896 mm)
137” (3480 mm)
8’1” to 9’0”
12”, 15” Radius
126” (3200 mm)
168” (4267 mm)
HEADROOM REQUIREMENTS
Track Type
Space Needed
12” Radius
13-1/2” (343 mm)
15” Radius
14-1/2” (368 mm)
Weatherstrips
Level heade
r
Finished
Door width
Jamb
s
Backroo
m
Plumb
jambs
Finished
Door
Height
Nail
Headroom
Header board 2”x 6”
lumber preferred
Suitable mounting surface
2”x 6” lumber minimum
Weatherstrips
Jamb
Quick Install track
Other track systems
Jamb
1/8” to 1/4”
Min. Side
room
Clearance
is 3 1/2”
Min. Side
room
Clearance
is 3 1/2”
Package Contents
NOTE:
Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Door sections (as required)
Torsion shaft / Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Vertical tracks RH/LH (as required)
Q.I. flag angles RH/LH (as required)
F.A. flag angles RH/LH (as required)
Riveted vertical track assemblies RH/LH (as required)
Horizontal tracks RH/LH (as required)
Angle mount vertical track assemblies RH/LH (as required)
(2) Horizontal angles (as required)
Q.I. jamb brackets
(as required)
F.A. jamb brackets
(as required)
Weather seals & nails
(If included)
Drawbar
operator bracket
Pull Down rope
(if included)
Track rollers
(as required)
Strut (U-shaped)
(if included)
Strut (A-symmetrical)
(if included)
Top fixture
bases (as required)
Top fixture
slides (as required)
Roller
slides (as required)
Winload jamb
brackets (as required)
(2) Top fixture roller
slides (as required)
Reinforcement
brackets
(as required)
End bearing bracket RH/LH (as required)
Cable drums RH/LH
Torsion springs RH/LH
Counterbalance lift cables
Center bracket (as required)
Center bracket bearing
(as required)
Center coupler
assembly (as required)
Keys
(as required)
1/4”-14 x 7/8” Self
drilling screws (as required)
5/16” x 1-1/4”
Clevis pin
Cotter pin
1/4”-20 x 11/16” Self
drilling screws (as required)
(2) #12 x 1/2”
Phillips head screws
3
