Wavtech LinkT Owner'S Manual Download Page 3

 

ROUTE WIRING AWAY FROM SHARP EDGES AND MOVING PARTS.

 Arrange cables and 

wiring away from sharp or pointed edges and avoid moving parts such as seat hinges or 
rails to prevent pinching or wear. Use loom protection where appropriate and always use 
a grommet for any wiring routed through metal. 

 NEVER RUN SYSTEM WIRING OUTSIDE OR UNDERNEATH THE VEHICLE.  

All wiring 

must 

be routed, secured and protected inside the vehicle. Failure to do so may result in 

fire, injury or property damage.

 

INSTALL THE UNIT IN A DRY AND VENTILATED LOCATION.

 Avoid mounting locations 

where the unit will likely be exposed to high moisture or heat without adequate 
ventilation.  Moisture penetration or heat buildup may result in product failure.

 

REDUCE GAIN AND SOURCE VOLUME TO MINIMUM LEVELS FOR INITIAL SYSTEM 

TUNING AND BEFORE CONNECTION TO AN AMPLIFIER.

 Ensure amplifier power is off 

before connecting RCA cables and follow proper system gain setting procedures. Failure 
to do so may result in damage to the amplifier and/or connected components. 

 Package Contents:

Main Unit

Terminals

(2pcs, detachable)

Accessories Required for 
Installation 

(not included)

:

Mounting Tabs

(2pcs, detachable)

Ÿ

RCA Interconnects

Ÿ

18AWG Wire

Ÿ

In-line Fuse Holder w/1A fuse

Ÿ

Battery Ring Terminal

Ÿ

Ground Terminal

Ÿ

Wire Crimp Connectors

Ÿ

Grommets and Loom

Ÿ

Cable Ties 

Ÿ

Mounting Screws 

2

 

Introduction

 Welcome to Wāvtech, exceptional mobile audio integration products for 
audiophiles. Our products are engineered to provide a truly remarkable 
listening experience. Built for the professional installer, our OEM integration 
and signal processor models are simply the best solution available for unlimited 
sound system upgrades while retaining the factory receiver.

Features

Ÿ

2-Channel Digital Time Alignment Processor

Ÿ

2-Channel Line Output Converter or Line Driver

Ÿ

Differential Balanced Inputs

Ÿ

Low Impedance Outputs

Ÿ

Independent Variable Gains with Clip LEDs

Ÿ

Auto Turn-On via DC-Offset or Audio Signal Detect

Ÿ

Gen12V Remote Output

Ÿ

OEM Load Detect Compatible

Ÿ

Selectable Ground Isolation

Ÿ

Detachable Power and Speaker Input Terminals

Ÿ

Professional Grade Panel Mount RCA Output Jacks

Ÿ

Aluminum Chassis w/Detachable Mounting Tabs

Summary of Contents for LinkT













Reviews: