Wavelength Electronics LFI-3500 Series User Manual Download Page 9

9

NOTE!

Complete all operational steps in the order provided.  Skipping
a step can result in damage to the device being controlled or
the Thermoelectric Module.  Start with the section appropriate
to the type of sensor you are using

WARNING

For continued protection against fire, replace line fuse only with
fuse specified, type and rating.

ATTENTION

Pour une protection permanente contre les risques d’incendie,
ne remplacer les fusibles secteur que par des fusibles
conformes aux spécifications.

VORSICHT

Defekte Sicherungen sind nur durch die angegeben Typen und
mit den spezifizierten Werten zu ersetzen um die Sicherheit des
Gerätes zu gewährleisten.

CAUTION

RISK OF ELECTRICAL SHOCK.  Do not power on this
instrument if the case is damaged or any of the covers or
panels are removed.  NO USER SERVICEABLE PARTS
INSIDE.

ATTENTION

Risque d’Electrocution.  Ne pas mettre sous tension cet
instrument si le boîtier est endommagé ou si les capots ou les
faces sont retirés.  Aucun composant réparable par l’utilisateur.

VORSICHT

Hochspannung.  Im Falle eines Gerätedefektes oder bei
geöffneter Verkleidung Netzstecker ziehen!  Gerät kann und
braucht vom Anwender nicht gewartet werden.

CAUTION

POSSIBLE ELECTRICAL SHOCK OR FIRE HAZARD.  Do not
expose the LFI Temperature Controller to rain or moisture.  Do
not operate this instrument in the presence of flammable gases
or fumes.

ATTENTION

Risque d’électrocution ou d’incendie.  Ne pas exposer
l’alimentation LFI à la pluie ou à l’humidité.  Ne pas utiliser cet
instrument en présence de gaz inflammable ou de fumée.

VORSICHT

Brandgefahr und Gefahr eines elektrischen Schocks!  Setzen
Sie das Gerät nicht dem Regen oder der Feuchtigkeit aus.
Schalten Sie das Gerät in der Gegenwart entflammbarer Gase
oder Dämpfe nicht ein!

 !

Summary of Contents for LFI-3500 Series







































Reviews: