Wavelength Electronics HTC 4000 Manual Download Page 6

HTC4000 TEMPERA

TURE CONTROLLER

www.teamwavelength.com

© 2012

HTC4000-62400-B

PAGE 6

The HTC Series Temperature Controller is a linear 

controller designed for stable, low noise operation.  

We recommend using a regulated, linear supply 

for optimum performance.  Depending on your 

requirements, you may be able to use a switching 

power supply.  [A switching power supply will affect 

noise and stability.] 

The recommended operating voltage is b5 V 

and +12 V.  The voltage available to the thermoelectric 

is the “Compliance Voltage.”  Compliance voltage 

varies with the input voltage.

A heatsink is required to properly dissipate heat from 

the HTC mounting surface.  Maximum internal power 

dissipation is 17 Watts.

Special attention to grounding will ensure safe operation.  

Some  manufacturers  package  devices  with  one  lead 

of the sensor or thermoelectric connected to the metal 

enclosure or in the case of laser diodes, the laser 

anode or cathode.

WARNING:  Precautions should be taken not to 

earth ground pins 11, 12, or 13.  If any of these pins 

are earth grounded, then pins 5, 10, and 14 must be 

floating with respect to earth ground.

POWER SUPPLY AND NOISE

GROUNDING

Unless Earth and Instrument Ground are

connected via the power supply, Instrument Ground

is floating with respect to Earth Ground

Earth Ground on

USA 115 VAC wall socket

Common or

Instrument Ground

EARTH

DC POWER SUPPLY

-

+

Summary of Contents for HTC 4000
















Reviews: