wattstopper DT-355 Installation Instructions Manual Download Page 1

Page: 1 / 13

DT-355

360° Dual Technology • Line Voltage

Occupancy Sensor

with Light Level feature

SPECIFICATIONS

Voltages . . . . . . . . . . . . . . . . . . .120/230/277/347VAC, 50/60Hz

Load Requirements

@120VAC, 50/60Hz . . . . . . . . . . . 0-800W Ballast/Tungsten

@230 or 277VAC, 50/60Hz . . . . . . . . . . . . . 0-1200W Ballast

@347VAC, 50/60Hz . . . . . . . . . . . . . . . . . . . 0-1500W Ballast

Operating Temperature . . . . . . . . . . 32° to 131°F (0° to 55°C)

Terminal Torque Rating . . . 4.428 inch pound-force. (0.5Nm)

Light Level One-Step Adjustment . . . . . . . . . . . . 10FC–300FC

Time Delay Adjustment. . . . . . . . . . . . . . . . . . . 5 to 30 minutes

Walk-Through Mode .3 minutes if no activity after 30 sec.

Test Mode 5 sec. upon intial power-up or DIP switch reset

PIR Coverage (Typical) . . . . . . . . . . . . . . . . . . . . . . . . . 1200 ft2

Sensitivity Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . .Automatic or Low (DIP switch setting)

Ultrasonic Coverage (Typical) . . . . . . . . . . . . . . . 800-1200 ft2

Sensitivity Adjustment. . .Minimum to Maximum (trimpot)

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40kHz

Installation Instructions

U.S. Patents: 5,189,393

and Patent Pending

Summary of Contents for DT-355














Search results

Summary of Contents for DT-355

Reviews:

Related manuals for DT-355

Brands by name

Popular brands

wattstopper DT-355, Installation Instructions Manual

Search results

Summary of Contents for DT-355

Reviews:

Related manuals for DT-355

Brands by name

Popular brands