background image

19

BACNET SNOW/ICE SENSOR INTERFACE 681

Literature

IOM-T-681, IS-T-681, F-T-681, ES-T-681

Control

Microprocessor control. This is not a safety (limit) control.

Packaged weight

4.3 lb. (1960 g)

Dimensions

6.35" H x 5.13" W x 1.30" D (161 x 130 x 33 mm)

Display

3.5", color touchscreen

Enclosure

Blue PVC plastic, NEMA type 1

Approvals

BTL Certified & CAN ICES-003 (A) / NMB-003 (A) & FCC Part 15B (A)

Ambient conditions

-4 to 122°F (-20 to 50°C), < 90% RH non-condensing, outdoor use permitted 
when used in NEMA 3 enclosure

Power supply

24 V (ac) ±10%, 50 and 60 Hz, 17 VA Class 2

Communications

BACnet MS/TP

Sensors

NTC thermistor, 10 kΩ @ 77°F (25°C ±0.2°C) ß=3892

– Required

Snow/Ice Sensor 090 and Snow / Ice Sensor Socket 091 or Snow Sensor  
095 & Slab Sensor 072 (depends on the bundle configuration)

– Optional

tekmar type: 070

Error Messages (2 of 2) 

continued

Description

SNOW SENSOR BROWN WIRE ERROR

The Interface is unable to read the brown wire connected to sensor . Check the sensor brown and 

black wires according to the sensor installation manual . Once the error has been corrected, the 

error message automatically clears .

SNOW/ICE SENSOR ERROR

The Interface is unable to properly detect the sensor . Check the sensor brown, yellow, red and black wires 

according to the sensor installation manual . It is important to check any cable splices for loose  

wiring connections . Once the error has been corrected, the error message automatically clears .

SNOW SENSOR ERROR

The Interface is unable to properly detect the snow sensor . Check the snow sensor yellow, red and 

black wires according to the sensor installation manual . Once the error has been corrected, the 

error message automatically clears .

Technical Data

Summary of Contents for tekmar 681





















Reviews: