background image

Enclosure C 

 --------------------------------------------------------

Enclosure C is designed for smaller controls and their wiring. This enclosure 

has either a large or a small window opening depending on the control used.

Mounting the C Enclosure 

 ------------------------------------------

Grasp  the  front  cover  by  the  fingertip  grips  on  the  top  and  bottom  of  the 

enclosure  and  pull  the  front  cover  off.  Remove  the  wiring  cover  screw.  The 

enclosure is either mounted flush onto a wall or it can be placed onto a 2” x 4” 

electrical box. The mounting holes in the enclosure accept #6 screws. Wiring 

to  the  control  enters  the  wiring  chamber  through  the  back  or  bottom  of  the 

enclosure. To reassemble the enclosure, first replace the wiring chamber cover 

and then push the front cover onto the enclosure until it snaps into place.

STEP TWO 

 CONTROL INSTALLATION 

STEP THREE 

 SENSOR INSTALLATION 

Caution:

  Do not run sensor wires parallel to telephone or power cables.  If the sensor wires are located in an area with strong sources 

of electromagnetic interference, shielded cable or twisted pair should be used or the wires can be run in a grounded metal conduit.  

If using shielded cable, the shield wire should be connected to the Sensor Common terminal on the control and not to earth ground. 

All electrical wiring terminates in the two wiring chambers on the control. If the control is to be mounted on an electrical box, the wiring 

can be roughed-in at the electrical box prior to installation of the control.

Power must not be applied to any of the wires during the rough-in wiring stage.

Install the Outdoor Sensor and Universal Sensor according to the directions on the following page.

© 2019 tekmar  256_D - 09/19

9 of 20

Summary of Contents for Tekmar 256





















Reviews: