Watts PVi CENTURION Installation, Operation And Maintenance Manual Download Page 64

Page: 64 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 6: SAFETY DEVICE TESTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 64 of 131

6.11 CHECK IGNITION SWITCH OPEN DURING IGNITION

The

Ignition

switch (and the

Purge

switch) is located on the Air/Fuel Valve. To check the

switch, proceed as follows:

Set the Controller’s

Enable/Disable

switch to

Disable

2. Go to

Main Menu

→

Diagnostics

→

Manual Run

and enable

Manual Mode

3. Set the valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

4. Remove the Air/Fuel Valve cover (Figure 6-10, above) by rotating counterclockwise.

5. Remove wire #1611 or #1612 from the Ignition switch (Figure 6-11).

Set the Controller’s

Enable/Disable

switch to

Enable

to start the unit.

7. The unit begins its start sequence and then shut down and display

Ign Switch Open

During Ignition

8. Replace wire on the Ignition switch and press

CLEAR

button. The unit should restart.

Figure 6-11: Air/Fuel Purge and Ignition Locations

6.12 SAFETY PRESSURE RELIEF VALVE TEST

Test the safety Pressure Relief Valve in accordance with ASME Water Heater and Pressure
Vessel Code, Section VI.

Summary of Contents for PVi CENTURION




































































































































Search results

Summary of Contents for PVi CENTURION

Reviews:

Related manuals for PVi CENTURION

Brands by name

Popular brands

Watts PVi CENTURION, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for PVi CENTURION

Reviews:

Related manuals for PVi CENTURION

Brands by name

Popular brands