background image

 

LYNC UV-H 

SECTION 9: LYNC UV-H LIMITED WARRANTY  

    

 

SECTION 9: LYNC UV-H LIMITED WARRANTY 

Limited Warranty for LYNC UV-H Ultraviolet Water Disinfection Systems purchased in Canada, the 
United States, Australia and New Zealand only. For systems purchased outside of North America, the 
original manufacturer

’s warranty (available at: www.uvpure.com/warranty/) may provide additional 

coverage for system components manufactured by UV Pure Technologies. Please see the manufacturer

’s 

warranty for additional details.  

What this warranty covers: 

Defects in materials and workmanship in systems sold by Lync by Watts including Hallett

®

 systems, 

replacement UV lamps and other original equipment manufacturer components such as manifolds or 
NEMA cabinets sold or certified by Lync by Watts. 

What the period of coverage is for System Parts: 

Five-year Limited Warranty for structural, hardware, and mechanical components. Specifically, this 
includes the following system parts: system casing (machined and extruded aluminum parts, stainless 
steel parts, and plastic molded components), stainless steel manifolds, NEMA cabinets, welded steel 
skids and structural components, and stainless steel self-cleaning mechanism. 

Three-year Limited Warranty for electrical components, reflectors, and quartz sleeve. Specifically, this 
includes the following system parts: wiper motor, air blowers, circuit boards, ballast and micro-
processor with digital display, wiring harnesses, lamp sockets, reflectors, and quartz sleeves. 

One-year Limited Warranty sensor probes and purge valves. Specifically this includes the following 
system parts: UV sensors and the circuit board they are mounted in, temperature probes, and purge 
valves.    

12-month Limited Warranty for all replacement LPHO lamps (coverage applies up to two years from 
the date of manufacture of the lamps). 

16-month Limited Warranty for all replacement amalgam lamps 

Ninety-day Limited Warranty or Balance of Original Warranty for replacement Parts. Specifically this 
includes any system parts replaced or repaired under this Limited Warranty. This warranty period is for 
the balance of the original warranty or for 90 days from the date the Part is repaired and/or returned to 
the first end-user whichever is longer. An exception is all replacement lamps that are covered for 12 or 
16 months from date of replacement depending on lamp type. 

Who is covered: 

This Limited Warranty extends to you only if you are the FIRST END-USER PURCHASER and with respect 
to the ORIGINAL INSTALLATION; 

the warranty period shall commence upon the Date of Purchase. 

What we will do to correct problems covered by this Limited Warranty: 

During the warranty period, as set out above, Lync by Watts will repair or replace Products or Parts, at 
its sole discretion and cost, with the exception of shipping and handling charges. Lync by Watts may 
require that certain failed part be returned to Lync by Watts within 45 days for analysis and to facilitate 
continuous improvement; for example, circuit boards and sensors that fail must be returned to Lync by 
Watts. Replacement parts or systems may be functionally equivalent reconditioned/refurbished/pre-
owned or new products or parts at Lync by Watts

’ sole discretion. Lync by Watts may provide software 

updates, at its discretion, but is under no obligation to do so.  

How to get help: 

Call a Lync by Watts representative. A complete list of representatives and their coverage areas is 
available on Lync by Watts

’s website: www.LyncbyWatts.com.   

 

 

Summary of Contents for LYNC UV-H









































Reviews: