background image

 

 

Page 16 of 18 

 

WARRANTY 

 

 

WHAT YOUR WARRANTY COVERS: 
 

If any part of your Watts Pure Water Treatment Device is defective in workmanship (excluding replacement filter elements), return the 
unit within 1 year of date of original purchase. Watts will repair or, at WATTS option, replace it at no charge. 

 
HOW TO OBTAIN WARRANTY SERVICE: 

 
Contact WATTS  customer service department (1-888-774-7405) to obtain a Return Goods Authorization Number (RGA#).  Model and 

Serial Number are required for obtaining an RGA #.  For warranty service, ship your water treatment device with the RGA # printed on 
the Shipping Label to Watts, freight and insurance prepaid, with proof of original purchase date.  Watts will repair or replace the water 

treatment device and ship it back to you prepaid. 
 

WHAT YOUR WARRANTY DOES NOT COVER: 
 

This warranty does not cover defects resulting from improper installation, customer abuse, misuse, misapplication, improper 
maintenance, neglect, alteration, accidents, casualties, fire, flood, freezing, heat, environmental factors or acts of nature.  

 
This warranty will be voided if defects occur due to failure to observe the following conditions:   

 

1. The water treatment device must be hooked up to a potable municipal water supply. 

 

2. The pH of incoming water must not be lower than 6.0 or higher than 8.5. 

 

3. The incoming water pressure must be between 25 psi and 80 psi.   If water pressure exceeds 80 psi a pressure regulator 

must be      installed. 

 

4. Incoming water temperature cannot exceed 100

°

 F (40

°

 C). 

 

This warranty does not cover any equipment that has been relocated from the site of its original installation. 
  

This warranty does not cover equipment that is installed outside North America. 
 

LIMITATIONS AND EXCLUSIONS: 
 

Watts WILL NOT BE RESPONSIBLE FOR ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE. 

 
WATTS WILL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING TRAVEL EXPENSES, 

TELEPHONE CHARGES, LOSS OF REVENUE, LOSS OF T IME, INCONVENIENCE, LOSS OF USE OF THE EQUIPMENT, AND DAMAGES 
CAUSED BY THE EQUIPMENT AND ITS FAILURE TO FUCTION PROPERLY. 

 

THIS WARRANTY SETS FORTH ALL OF WATTS’S RESPONSIBILITIES REGARDING THIS EQUIPMENT. 
 

OTHER CONDITIONS: IF Watts chooses t o replace the equipment, Watts may replace it with reconditioned equipment.   Parts used in 
repairing or replacing the equipment will be warranted for 90 days from the date the equipment is returned to you or for the remainder 

of the original warranty period, whichever is longer.   This warranty is not assignable or transferable.  
 

YOUR RIGHTS UNDER STATE LAW: 
Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of 

incidental or consequential damages, so the above limitations or exclusions may not apply to you.  This warranty gives you specific 
legal rights. You may have other legal rights, which vary from state to state. 

 

 
 

 

 
 

Summary of Contents for HS Series



















Reviews: