Watts HF scientific Air Sentinel II 110010 Installation And Operation Manual Download Page 7

7

Lamp Color Matrix

Meaning

Power Out

Both lamps GREEN

Safe Operation

Power ON

TIMER Lamp RED

Instrument Purging

 

Power OFF

PRESSURE lamp RED

Unsafe Operation 

Pressure Low

Power OFF

NO Lamps

 

No power out applied

  

No power applied; 

everything off

Purpose

Location

Label

Product name and 
certifications

Front of Air Sentinel II

Serial number, 
manufacturer, 
part number, 
power rating, 

CE & UL marking

Front of Air Sentinel II

Warning and 
informational

Front of Air Sentinel II

6.0 Instrument Labels

The following labels should be applied to the outside of the enclosure:

PRINTER SET UP

PRINT IN CMYK

WIDTH 3.25 INCHES

HEIGHT 4.0 INCHES

OFFSET

HORIZONTAL 66

VERTICAL 0

 PRINT PROCESS

PRESSURIZED ENCLOSURE

L# 74055

Minimum Over Pressure: ≥ 0.6 Millibar

Maximum Over Pressure:  4 Millibar

Minimum Purge Flow Rate:  35 SLPM

Minimum Purging Duration:  3 Minutes

Maximum Leakage Rate:      45 LPM

Electrical Compartment shall not be opened unless all power 

has been removed!

PRESSURIZED ENCLOSURE

L# 74055

Minimum Over Pressure: ≥ 0.6 Millibar

Maximum Over Pressure:  4 Millibar

Minimum Purge Flow Rate:  35 SLPM

Minimum Purging Duration:  3 Minutes

Maximum Leakage Rate:      45 LPM

Electrical Compartment shall not be opened unless all power 

has been removed!

Summary of Contents for HF scientific Air Sentinel II 110010









Reviews: