Installation
1.
Before beginning installation determine the system pressure.
a.
Open a faucet to allow the system pressure to equalize.
b.
Close faucet.
c.
Read the system pressure at the pressure gauge (Figure 1).
2.
The expansion tank pre-charge must be set to the system pressure as
determined in Step 1. Pre-charge prior to installation in the system.
Caution:
Pre-charge prior to installation in the system.
Do not adjust the air pre-charge of the expansion tank
with the system under pressure. The air pre-charge
should only be adjusted under zero system pressure.
Note:
The normal pre-charge is 20psi (138 kPa).
Do not exceed 80psi.
If system pressure exceeds
80psi (5.5 bar) it will be necessary to either:
A.
Add a
pressure reducing valve to the system or,
B.
Locate the
expansion tank in a riser where the static pressure is
below 80psi (5.5 bar).
a.
Unscrew the protective cap from the air inlet valve.
b.
Using a tire pressure gauge, check the tank pre-charge pressure.
c.
If necessary, pressurize the tank to the proper setting using a manual
bicycle tire pump.
Caution do not exceed 80psi.
d.
Replace the protective air cap.
3.
Shut off the water supply valve.
4.
Shut off power source to the water heater, (electricity, gas, oil burner
switch) and drain system following water heater manufacturer
recommendations.
5.
Install the expansion tank in the system (refer to Figure 1).
a.
The weight of the expansion tank filled with water is supported by
the system piping. Therefore, it is important that, where appropriate,
the piping has suitable bracing (strapping, hanger, brackets).
b.
The expansion tank may be installed vertically (preferred method)
or horizontally.
Caution: The tank must be properly supported
in horizontal applications.
c.
This expansion tank, as all expansion tanks, may eventually leak.
Do not install without adequate drainage provisions.
6.
Turn on the water supply valve.
7.
Open a hot water fixture and allow water flow until all air is removed from
the system.
8.
Reapply power to the water heater.
9.
Open a hot water fixture to allow a slight flow until the hot water has
reached operating temperature.
10.
Recheck system pressure following Step 1.a through c.
Caution:
Pre-charge prior to installation in the sys-
tem. Do not adjust the air pre-charge of the expan-
sion tank with the system under pressure. The air
pre-charge should only be adjusted under zero sys-
tem pressure.
If necessary, adjust the pressure reducing valve to the
expansion tank pre-charge as determined in Step 2.
Important!
• A pressure relief valve sized and installed in accor-
dance with local codes must be incorporated in
the systems requiring a combined temperature
and pressure safety relief valve. The temperature
and pressure safety relief valve should be sized
and installed in accordance with local codes.
• Never plug a safety Relief Valve.
Figure 1
(Optional Location)
Support Tank
in Optional
Horizontal
Position
(Optional Location)
Watts
Pressure
Gauge
Watts
Backflow Preventer
Water
Supply
Watts
Shutoff
Valve
Watts Pressure
Reducing Valve
Expansion
Tank
Water
Heater
To System
Watts
T&P
Safety
Relief
Valve
Floor Drain
Discharge Line
Air Inlet Valve
IS-DET
-M1
0910
EDP# 1915323
© Watts, 2009
USA:
815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
Canada:
5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
W a t e r S a f e t y & F l o w C o n t r o l P r o d u c t s
Limited Warranty:
Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of
original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER
WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting
from labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no
control. This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights.
SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
