5
CIVIC1-MOI-IT-W-ML-09-18-Rev.1
Watts Water Technologies, Inc.
EN
Once the correct power is supplied, the control unit carries out
the following phases in sequence:
LED and buzzer tests (about 5 seconds)
Whichever operating mode is selected, the LEDs will switch on
in sequence and the buzzer will sound briefly.
Warm-up of detectors (about 1 minute)
During this phase, which brings the detectors up to the
correct operating temperature, the gas detection system is not
operational. During this phase, if the wiring connections
are correct, the control unit display shows the following:
Operating test (about 3 minutes)
Once the detector warm-up phase is complete, the device
enters the operating test phase. During this phase, all internal
timing is reset to ease operating verification of the detectors
(alarm simulation). In this case, the control unit display shows
the following:
Keep the “Reset/Test” button pressed down for over 1 second
to interrupt the operating test phase. To test the detectors
correctly, proceed as follows:
Gas alarm test
Bring the test cylinder close to the detector grille and release
a small amount of gas (caution: if the gas is aimed directly at
the sensor, this will be permanently damaged). For CO testing
of detectors, smoked produced by combustion can be used.
The control unit will signal the alarm as follows:
Keep the “Reset/Test” button pressed down for 1 second to
silence the alarm (if there is no gas remaining) and terminate
the operating test phase. To restart the Test phase, just keep
the relative button pressed down for about 6 seconds. Repeat
the operations described above to test the other detectors.
Interface
Positive
logic
Negative
logic
Power supply LED
Green Flashing 1 Hz Flashing 1 Hz
General failure LED
Yellow On
Off
Detector failure LED (4) Yellow On
Off
Alarm and line failure
LED (4)
Red
On
Off
Alarm buzzer
No sound
No sound
Alarm relay
Energised
De-energised
Failure relay
Energised
De-energised
Interface
Positive logic
Negative logic
Detector
alarm LED
Red Off
On
Alarm buzzer
Continuous sound Continuous sound
Alarm relay
De-energised
Energised
(permanently or
pulsed depending
on E2)
Interface
Positive
logic
Negative
logic
Detector failure
LED
Yellow Off
On
Alarm buzzer
Intermittent
sound
Intermittent
sound
Failure relay
De-energised
Energised
General failure LED Yellow On
Off
Caution
The repeated use or high concentration of interfering
substances (alcohol, lighter fluid etc.) can cause permanen
damage to the sensor and put the device out of order.
Detector failure test
Simulate a failure in the detector as follows:
- disconnect the cable of the detector and verify the following alerts:
- reconnect the detector and press the “Reset/reconnect the
detector and press the “Reset/Test” to return the control unit to
normal operating mode, making the sure the conditions of the
various interfaces are reset.
Normal operation
This is the normal operating phase of the control unit during
which both gas alarm monitoring and self-testing of the
instrument (detector) and the system (control unit) are
active. During this phase, where there are no alarms and/or
abnormalities, the control unit display shows the following:
When dangerous concentrations of gas are detected, the
control unit enters the gas alarm phase and carries out the
following operations:
Once the gas alarm condition is normalised, the control unit
needs to be reset to its normal operating status. Press the
“Reset/Test button on the front of the control unit to reset it.
If there are abnormalities (detector and/or control unit), the con-
trol unit will show the following display:
Interface
Positive
logic
Negative
logic
Power supply LED
Green Flashing 2 Hz Flashing 2 Hz
General failure LED
Yellow On
Off
Detector failure LED (4) Yellow On
Off
Alarm and line failure
LED (4)
Red
On
Off
Alarm buzzer
No sound
No sound
Alarm relay
Energised
De-energised
Failure relay
Energised
De-energised
Interface
Positive
logic
Negative
logic
General failure LED
(for control unit failure)
Yellow Off
On
Detector failure LED
(for detector failure)
Yellow Off
On
Alarm buzzer
Intermittent
sound
Intermittent
sound
Failure relay
De-energised Energised
Interface
Positive
logic
Negative
logic
Power supply LED
Green On
On
General failure LED
Yellow On
Off
Detector failure LED (4) Yellow On
Off
Alarm and line failure
LED (4)
Red
On
Off
Alarm buzzer
No sound
No sound
Alarm relay
Energised
De-energised
Failure relay
Energised
De-energised
Interface
Positive logic
Negative logic
Detector
alarm LED
Red Off
On
Alarm buzzer
Continuous sound Continuous sound
Alarm relay
De-energised
Energised
(permanently or
pulsed depending
on E2)