INSTALLATION
According to Plumbing Codes this type of valve must
be installed as follows:
1. The valve must be installed at least 12" (305mm) above
the overflow level or flood rim of the fixture or container
being supplied.
2. The valve must be installed with the supply line con-
nected to the bottom or inlet of the valve and in a verti-
cal position where it is available for periodic inspection,
servicing and testing.
3. Because of possible water spillage due to valve opera-
tion, the valve must not be installed in a concealed lo-
cation, inside a wall, or where freezing or spillage will
cause water damage when a drain is not available.
4. See "IMPORTANT START-UP" message on reverse side.
CALIFORNIA PROPOSITION 65 WARNING
WARNING: This product contains chemicals
known to the State of California to cause cancer
and birth defects or other reproductive harm.
(Installer: California law requires that this
warning be given to the consumer.)
Service and Replacement Parts
Disassembly
1. Shut off the supply pressure and drain the valve.
2. Remove the two hood screws and the hood.
3. Place a wrench on the parallel flats of bonnet and
stem assembly. Turn counter clockwise and remove.
4. Remove the vent disc holder assembly.
5. Press down on the spring retainer and disengage it
from the retaining lugs. Then turn 90
°
and remove.
6. Remove the spring retainer and spring. Note that the
large diameter of the spring is down on the guide
assembly.
7. Remove the check disc holder and guide assembly.
8. Disassemble the check disc holder assembly.
Reassembly
Reassemble in the reverse order utilizing the new
parts from the repair kit.
Annual inspection of all water system safety and
control valves is required and necessary. Regular
inspection, testing and cleaning assures maximum
life and proper fuction.
Internal parts can be removed, repaired or inspected
without removing the valve from the piping.
Series 800 Repair Kits
Check Kits
Order No.
Kit No.
Sizes
0886027
RK800 CK
1
⁄
2
"
- 1"
0886028
RK800 CK
1
1
⁄
4
"
- 2"
Kit includes: Check disc assembly (disc and disc holder), Bonnet O-ring and
Spring.
Vent Float Kits
0886025
RK800 V
1
⁄
2
"
- 1"
0886026
RK800 V
1
1
⁄
4
"
- 2"
Kit includes: Float vent disc assembly (vent float, seal and spring) and Bonnet
O-ring.
Hood Screws
Air Chamber
Bonnet Seat
Test Cock
No. 2
Test Cock
No. 1
Check Valve Seat
Check Valve Disc
Body
Disc (holder) Float
Vent Disc
Bonnet
Hood
Check Valve
Quarter-turn
ball valve
Quarter-turn
ball valve
Bonnet Kits
Order No.
Kit No.
Sizes
0886023
RK800 B
1
⁄
2
"
- 1"
0886024
RK800 B
1
1
⁄
4
"
- 2"
Kit includes: Bonnet, Guide stem, Washer, Spring and Bonnet O-ring.
Rubber Parts Kits
0886021
RK800 RT
1
⁄
2
"
- 1"
0886022
RK800 RT
1
1
⁄
4
"
- 2"
Kit includes: Vent disc, Check disc and Bonnet O-ring.
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.wattsreg.com
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscda.com
IS-800 0033
EDP# 1910307
Printed in U.S.A.
©Watts Regulator Co., 1996
LIMITED WARRANTY: Watts Regulator Company warrants each product against defects in material and
workmanship for a period of one year from the date of original shipment. In the event of such defects
within the warranty period, the Company will, at its option, replace or recondition the product without
charge. This shall constitute the exclusive remedy for breach of warranty, and the Company shall not be
responsible for any incidental or consequential damages, including without limitation, damages or other
costs resulting from labor charges, delays, vandalism, negligence, fouling caused by foreign material,
damage from adverse water conditions, chemicals, or any other circumstances over which the Company
has no control. This warranty shall be invalidated by any abuse, misuse, misapplication or improper in-
stallation of the product. THE COMPANY MAKES NO OTHER WARRANTIES EXPRESS OR IMPLIED
EXCEPT AS PROVIDED IN THIS LIMITED WARRANTY.
