WattNode WNC-3Y-208-MB Installation And Operation Manual Download Page 62

62 Warranty

The accuracy of the solid-core CTs is specified from 10% to 100% of rated current. The phase 
angle error is specified at 50% of rated current. The CT suffix 

xxx

 is the rated current. The “N” at 

the end of the part number indicates a nickel core material, which is the only core material avail-
able for our solid-core CTs.

Model

Inside 

Diameter

Rated Amps (-xxx)

Accuracy / 

Phase Angle

Maximum 

Amps

CTT-0300-xxxN

0.30" (7.6mm)

5, 15, 20, 30

±1% / <1°

30

CTT-0500-xxxN

0.50" (12.7mm)

15, 20, 30, 50, 60

±1% / <1°

60

CTT-0750-xxxN

0.75" (19.0mm)

30, 50, 70, 100

±1% / <1°

100

CTT-1000-xxxN

1.00" (25.4mm)

50, 70, 100, 150, 200

±1% / <1°

200

CTT-1250-xxxN

1.25" (31.7mm)

70, 100, 150, 200, 250, 300, 400

±1% / <1°

400

Table 17: Solid-core CTs

Warranty

All products sold by Continental Control Systems, LLC (CCS) are guaranteed against defects in 
material and workmanship for a period of three years from the original date of shipment. CCS’s 
responsibility is limited to repair, replacement, or refund, any of which may be selected by CCS at 
its sole discretion. CCS reserves the right to substitute functionally equivalent new or serviceable 
used parts.

This warranty covers only defects arising under normal use and does not include malfunctions or 
failures resulting from: misuse, neglect, improper application, improper installation, water damage, 
acts of nature, lightning, product modifications, alterations or repairs by anyone other than CCS.

Except as set forth herein, CCS makes no warranties, expressed or implied, and CCS 
disclaims and negates all other warranties, including without limitation, implied warranties 
of merchantability and fitness for a particular purpose.

Limitation of Liability

In no event shall CCS be liable for any indirect, special, incidental, punitive or consequen-
tial damages of any kind or nature arising out of the sale or use of its products whether 
such liability is asserted on the basis of contract, tort or otherwise, including without 
limitation, lost profits, even if CCS has been advised of the possibility of such damages.

Customer acknowledges that CCS’s aggregate liability to Customer relating to or arising 
out of the sale or use of CCS’s products, whether such liability is asserted on the basis of 
contract, tort or otherwise, shall not exceed the purchase price paid by Customer for the 
products in respect of which damages are claimed.  Customer specifically acknowledges 
that CCS’s price for the products is based upon the limitations of CCS’s liability set forth 
herein.

Summary of Contents for WNC-3Y-208-MB































































Reviews: