manualshive.com logo in svg

WATSON Edison Rail Lamp, Assembly

The WATSON Edison Rail Lamp is an exquisite addition to your home decor, blending vintage charm with modern functionality. This versatile lamp requires assembly to bring its timeless beauty to life. Easily access the comprehensive assembly manual for free download from our website, ensuring a seamless setup experience.

Share
Download
background image

11 EDISON RAIL LAMP ASSEMBLY INSTRUCTIONS

Edison Senior: Replace Panels 

Attach the panels that were set aside in Step 1 by lifting and clipping them onto the rail clips.  
Secure the panels to the rail using the #8-32x1/4 screws that were set aside with the panels (2x per panel). 

9.

#8 X 3/4 

(Not included with light) 

Summary of Contents for Edison Rail Lamp















Reviews:

No comments

Related manuals for Edison Rail Lamp

Qlight S80S Manual preview
S80S
Brand: Qlight Pages: 3
qtran Q-VAULT-5 Installation preview
Q-VAULT-5
Brand: qtran Pages: 2
Q-Optics Radiant Instructions & Care preview
Radiant
Brand: Q-Optics Pages: 2
ubicquia 3i Installation Manual preview
3i
Brand: ubicquia Pages: 4
Kelvin Epos 300 User Manual preview
Epos 300
Brand: Kelvin Pages: 30
Feniex QUAD Q3 Manual preview
QUAD Q3
Brand: Feniex Pages: 5
Malibu Boats LZ605RP Instructions preview
LZ605RP
Brand: Malibu Boats Pages: 2
Keldan VIDEO 18XR 30000lm CRI82 Operating Instructions Manual preview
VIDEO 18XR 30000lm CRI82
Brand: Keldan Pages: 8
RUSTA 913013310102 Manual preview
913013310102
Brand: RUSTA Pages: 12
High End Systems SolaFrame 3000 User Manual preview
SolaFrame 3000
Brand: High End Systems Pages: 32
HAMPTON BAY 336-392 Instruction Manual preview
336-392
Brand: HAMPTON BAY Pages: 6
Zafferano LD1011N3 Instructions For Use Manual preview
LD1011N3
Brand: Zafferano Pages: 14
UniqueTek Light-Load II User Manual preview
Light-Load II
Brand: UniqueTek Pages: 2
Catellani & Smith U. F Up Assembly Instructions preview
U. F Up
Brand: Catellani & Smith Pages: 4
Eaton Halo RL560 Series Instructions Manual preview
Halo RL560 Series
Brand: Eaton Pages: 8
Malibu Boats LT406 Instructions preview
LT406
Brand: Malibu Boats Pages: 2
Larson Electronics EMGBALL-LED1-LV Instruction Manual preview
EMGBALL-LED1-LV
Brand: Larson Electronics Pages: 5
Waldmann ATARO DUW 2/D Series Instructions For Use Manual preview
ATARO DUW 2/D Series
Brand: Waldmann Pages: 84

Brands by name

Popular brands

Load more brands