WATSON 360.394.1300 Assembly Download Page 2

2  ESSENTIAL THREE-LEG DESK ASSEMBLY INSTRUCTIONS

Important Safety Instructions

DANGER - 

To reduce the risk of electric shock:

1.  Always unplug this furnishing from the electrical outlet before cleaning. 

WARNING - 

To reduce the risk of burns, fire, electric shock, or injury to persons: 

1.  Unplug from outlet before putting on or taking off parts. 

2.  Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons. 

3.  Use this furnishing only for its intended use as described in these instructions. Do not use attachments not    

 

   

recommended by the manufacturer. 

4.  Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or  

 

   

damaged, or dropped into water. Return the furnishing to a service center for examination and repair. 

5.  Keep the cord away from heated surfaces. 

6.  Do not use outdoors. 

7.  Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 

8.  To disconnect, turn all controls to the off position, then remove the plug from outlet. 

9.  WARNING: Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See    

 

 

              Grounding Instructions (Figure 77.1).

10.  Mount furnishings at the correct height.

This product is for commercial use only. 

Maximum intended load for this desk is 250 lbs (113 kg)

When using an electrical furnishing, basic precautions should always be followed, including the following:

Read all instructions before using (this furnishing).

Summary of Contents for 360.394.1300


















Reviews: