manualshive.com logo in svg

Watson-Marlow 720R, Installation, Operating And Maintenance Manual, Page: 67 / 127

Share
Download
Watson-Marlow 720R Installation, Operating And Maintenance Manual Download Page 67

20

MemoDose mode

Each time the pump is started by pressing

START

, it records the number of pumphead revolutions which

occur until

STOP

is pressed. The number of revolutions is proportional to the volume of fluid which has

been dispensed: the dose. MemoDose mode allows the user to repeat-dose a precise volume of fluid.
This can be achieved by dispensing a master dose, or entering a dose volume manually using the
keypad. MemoDose can repeat this dose exactly or proportionately.

20.1

To configure MemoDose

o

Select

MODE

o

Using the

∧

/

∨

keys, scroll to

MemoDose

and press

SETTINGS

Note: the pump must be stopped to enter MemoDose Settings.

20.2

Set flow rate

Using the

∧

/

∨

keys, scroll to

Flow rate

and press

SELECT

.

Using the

∧

/

∨

keys, enter the dose flow rate and press

SELECT

.

m-730un-en-08.1

67

Summary of Contents for 720R
































































































































Reviews:

No comments