Watson Marlow Pumps 500 Series Installation, Operating And Maintenance Manual Download Page 12

Page: 12 / 157

Pump specifications

Table 1 - Specification ratings

Operating temperature

5 °C to 40 °C (41 °F to 104 °F)

Storage temperature

530: -40 °C to 70 °C (-40 °F to 158 °F)

Humidity (non-condensing)

80 % up to 31 °C (88 °F) decreasing linearly to 50 % at 40 °C (104

°F)

Maximum altitude

2000 m (6560 ft)

Power Rating

530: 135 VA

Supply voltage

100-120 V/200-240 V 50/60 Hz 1 pH (Subject to regional cord sets

and supply)

Maximum voltage fluctuation

+/-10 % of nominal voltage. A well regulated electrical mains

supply is required along with cable connections conforming to

the best practice of noise immunity.

Full load current

530: <0.6 A @ 230 V; <1.25 A @ 115 V

Fuse rating

T2.5AH250V (5x20 mm)

Installation category
(overvoltage category)

Pollution degree

530: IP31 to BS EN 60529, if supplied with N module then IP66 to

BS EN 60529. Meets the requirements of NEMA 4X to NEMA 250 *

(indoor use - protect from prolonged UV exposure)

dB rating

530: < 70 dB (A) @ 1 m

Control ratio

530: 0.1-220 rpm (2200:1)

Maximum speed

530: 220 rpm

m-530pn-en-09 02-02-22

Summary of Contents for 500 Series






























































































































































Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands

Watson Marlow Pumps 500 Series, Installation, Operating And Maintenance Manual

Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands