Watlow L Series User Manual Download Page 2

Safety Information

We use note, caution and warning symbols throughout this book to draw your attention to 
important operational and safety information.
A “NOTE” marks a short message to alert you to an important detail.
A “CAUTION” safety alert appears with information that is important for protecting your 
equipment and performance. Be especially careful to read and follow all cautions that apply to 
your application.
A “WARNING” safety alert appears with information that is important for protecting you, oth-
ers and equipment from damage. Pay very close attention to all warnings that apply to your 
application.
The safety alert symbol, 

ç

 (an exclamation point in a triangle) precedes a general CAUTION 

or WARNING statement.
The electrical hazard symbol, 

Ó

 (a lightning bolt in a triangle) precedes an electric shock haz-

ard CAUTION or WARNING safety statement.

Warranty

These controllers are manufactured by ISO 9001-registered processes and are backed by a 
three-year warranty.

Return Material Authorization (RMA)

1. 
 
 

•  Ship to address   

 

 

• 

Bill to address 

 

• 

Contact 

name 

   • Phone 

number 

 

•  Method of return shipment 

 

• 

Your P.O. number

 

•  Detailed description of the problem 

• 

Any special instructions

 

•  Name and phone number of person returning the product.

2.  Prior approval and an RMA number, from the Customer Service Department, is needed  
 

when returning any unused product for credit. Make sure the RMA number is on the out 

 

side of the carton, and on all paperwork returned. Ship on a Freight Prepaid basis.  

3.  After we receive your return, we will examine it and try to verify the reason for the return.
4.  In cases of manufacturing defect, we will enter a repair order, replacement order or issue  
 

credit for material returned. 

5.   To return products that are not defective, goods must be be in new condition, in the origi- 
 

nal boxes and they must be returned within 120 days of receipt. A 20 percent restocking  

 

charge is applied for all returned stock controls and accessories.

6.  If the unit is not repairable, it will be returned to you with a letter of explanation. 
7.  Watlow reserves the right to charge for no trouble found (NTF) returns.

The Series L Limit user’s manual is copyrighted by Watlow Electric Manufacturing, © February 
2015 with all rights reserved. 

ç

CAUTION or 

WARNING

Ó

Electrical  

Shock Hazard

CAUTION or WARNING

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for L Series
























Reviews: