Setup, Chapter 4
26
WATLOW Series 942 User's Manual
Setup
dAtA
bAud
Addr
Prot
LOg
Int
tAg
PStr
Input Type
Sensor Range Low
Sensor Range High
J
32
°
F/0
°
C
1382
°
F/750
°
C
K (appears as H)
-328
°
F/-200
°
C
2282
°
F/1250
°
C
t
-328
°
F/-200
°
C
662
°
F/350
°
C
n
32
°
F/0
°
C
2282
°
F/1250
°
C
Pt2
32
°
F/0
°
C
2543
°
F/1395
°
C
c
797
°
F/425
°
C
4200
°
F/2315
°
C
r
32
°
F/0
°
C
2642
°
F/1450
°
C
S
32
°
F/0
°
C
2642
°
F/1450
°
C
b
*32
°
F/0
°
C
3092
°
F/1700
°
C
rtd (1
°
)
-328
°
F/-200
°
C
1112
°
F/600
°
C
rt.d (0.1
°
)
-99.9
°
F/-99.9
°
C
392.0
°
F/200.0
°
C
0-5 (VDC)
-5.00/-50.0/-500
35.00/350.0/3500
420 (mA)
-5.00/-50.0/-500
35.00/350.0/3500
* b t/c: Useable
range is suggested
to be 1598 to 3092
°
F
or 870 to 1700
°
C.
Range is at 32
°
to
allow using at low
temperatures
without range low
sensor errors.
NOTE:
Profile Start:
Selects whether the profile starts at the current set point value or
the current process value.
Range:
Proc or StPt
Range:
StPt
Baud:
Represents the current baud rate for serial communications. This
parameter appears if your Series 942 has communications.
Range
: 300, 600, 1200, 2400, 4800, 9600
Default:
1200
Data:
Allows the user to select the data bits and parity for communication.
This parameter appears if your Series 942 has communications.
Range:
7 o = 7 data bits and odd parity
Default:
7 o
7 E = 7 data bits and even parity
8 n = 8 Data bits and no parity
Protocol:
Selects the communication protocol. This parameter appears if your
Series 942 has communications.
FULL = ANSI X3.28 2.2 - A.3
On = XON - XOFF
Range:
FULL or On
Default:
FULL
Address:
Selects the address for this unit if Prot = FULL. This parameter
appears if your Series 942 has communications.
Range:
0 to 31
Default:
0
Log:
Selects the data logging function for a printout of the data. This parame-
ter appears if your Series 942 has communications, and Prot = On.
Range:
On or OFF
Default:
OFF
Interval:
Selects the time interval for the logging function This parameter
appears if your Series 942 has communications, Prot = On, and Log = On.
Range:
0.0 to 60.0 minutes
Default: 0.0
Tag:
Selects what variables are to be transmitted out during the data logging
function. This parameter appears if your Series 942 has communications,
Prot = On, and Log = On.
P = Process
S = Set Point
A = Auxiliary Status
Range:
PSA, PS-, P-A, P--, -SA, -S-, --A, ---
Default:
---
Table 1- Input Ranges
