Page 30
START-UP AND REFILL PROCEDURES
Your Hot Spring
®
spa has been thoroughly tested during the manufacturing process to ensure reliability and long-term customer satisfaction. A
small amount of water may have remained in the plumbing after testing and, as a result, may have spotted the spa shell or the spa siding prior to
delivery. Before filling the spa, wipe the spa shell clean with a soft rag.
The following instructions must be read and followed exactly to ensure a successful start-up or refill.
CAUTIONS
•• D
Do
o nno
ott ffiillll tthhee ssp
paa w
wiitthh hho
ott w
waatteerr,, aass ttrriip
pp
piinng
g o
off tthhee hhiig
ghh--lliim
miitt tthheerrm
mo
ossttaatt m
maayy rreessuulltt..
•• D
DO
O N
NO
OT
T C
CO
ON
NN
NE
EC
CT
T P
PO
OW
WE
ER
R T
TO
O A
AN
N E
EM
MP
PT
TY
Y S
SP
PA
A.. P
Po
ow
weerr tto
o tthhee ssp
paa aauutto
om
maattiiccaallllyy aaccttiivvaatteess ccrriittiiccaall cco
om
mp
po
onneennttss w
wiitthhiinn tthhee ssp
paa,,
ssuucchh aass cco
onnttrro
ollss,, hheeaatteerr,, cciirrccuullaattiio
onn p
puum
mp
p,, aannd
d o
otthheerr ssyysstteem
mss.. IIff p
po
ow
weerr iiss ssuup
pp
plliieed
d tto
o tthheessee cco
om
mp
po
onneennttss p
prriio
orr tto
o tthhee ssp
paa b
beeiinng
g
ffiilllleed
d,, tthhee cco
om
mp
po
onneennttss w
wiillll b
bee d
daam
maag
geed
d,, aannd
d tthhiiss m
maayy rreessuulltt iinn aa nno
onn--w
waarrrraannttyy cco
om
mp
po
onneenntt ffaaiilluurree..
•• D
Do
o nno
ott uussee yyo
ouurr ssp
paa aafftteerr ffiilllliinng
g uunnttiill aallll o
off tthhee sstteep
pss lliisstteed
d b
beello
ow
w aarree cco
om
mp
plleetteed
d..
•• D
Do
o nno
ott aad
dd
d cchhllo
orriinnee iiff ttrreeaattiinng
g yyo
ouurr ssp
paa w
wiitthh p
po
ollyyhheexxaam
meetthhyylleennee b
biig
guuaanniid
dee ((B
Biig
guuaanniid
dee,, P
PH
HM
MB
B,, eeg
g.. B
Baaq
quuaaS
Sp
paa
™
)) ssaanniittiizzeerr..
1. Close all drains and fill the spa with water through the filter compartment. Your Hot Spring spa water level should be maintained
approximately 1-1/2” above the top of the highest jet.
R
RE
EC
CO
OM
MM
ME
EN
ND
DE
ED
D:: Use the FreshStart
®
10,000
pre-filter to remove unwanted contaminants from the tap water.
IIM
MP
PO
OR
RT
TA
AN
NT
T:: Watkins Manufacturing Corporation does not recommend that the spa be filled with “softened” water, as this may damage the
spa’s equipment.
2. A
AF
FT
TE
ER
R the spa has been filled with water and the equipment compartment door is secured, power must be applied to the spa.
• 111155 vvo
olltt m
mo
od
deellss:: Connect the GFCI to the waterproof receptacle and push the RESET button on the GFCI.
• 223300 vvoolltt m
mood
deellss:: Open the door of the electrical subpanel, if your spa is a Grandee
®
, Vanguard
®
, Sovereign
®
(II), Accolade
™
or a 230 volt
converted model reset the 20 amp GFCI breaker first and verify the system is primed (see step 3), then reset the 30 amp breaker. If your
spa is a Vista
®
or Envoy
®
model reset the 30 amp GFCI breaker first, verify the system is primed, then reset the 20 amp breaker. Close
and secure the subpanel door.
3. The jet pump, heating system, and all internal plumbing will achieve a partial prime as the spa is filled. To check the operation of the jet
system and to purge any remaining air from the heating system, push the JETS button (for the Vista, Grandee, and Envoy push the JETS 1
and JETS 2 buttons, push the JETS 2 button a second time on the Vista and Envoy ) to make the jet pump run on high speed for one minute.
Once the jet system is fully operational (as indicated by strong, non-surging jets), priming of the spa is complete. Weak or surging jets are an
indication of a low water level condition or clogged filter cartridges.
IIM
MP
PO
OR
RT
TA
AN
NT
T:: Be sure the air control valves (see illustration in Comfort Control
®
system section) are open by turning each one clockwise and
checking to see that the SmartJet
®
lever is pointing to the 3 o’clock position (see illustration in SmartJet system section).
4. Adjust Total Alkalinity (TA) to 125 ppm, Calcium Hardness (CH) to 150 ppm, then spa water pH to between 7.4 and 7.6. These procedures are
listed in the “Water Quality and Maintenance” section.
IIM
MP
PO
OR
RT
TA
AN
NT
T:: Add spa water chemicals directly into the filter compartment with the jet pump on high speed for at least ten minutes.
O
OP
PE
ER
RA
AT
TIIO
ON
N N
NO
OT
TE
E:: Adjusting the Total Alkalinity as the first step is important, as out-of-balance TA will affect your ability to adjust the pH
correctly and will prevent the sanitizer from operating effectively.
5. Superchlorinate the spa water by adding 1-1/2 teaspoons of chlorine (sodium dichlor) per 250 gallons (950 liters) of spa water. Use the jet
button marked “CLEAN” to circulate the spa water for a ten-minute period.
6. During the super-chlorination period, rotate the SmartJet lever(s) through each of their operating positions, letting the spa water circulate (with
jets on) for equal periods of time. For example, if your spa has four operating positions, leave the SmartJet lever in each position for
approximately two to three minutes.
O
OP
PE
ER
RA
AT
TIIO
ON
N N
NO
OT
TE
E:: The Vista, Grandee, Envoy, Vanguard (V/VV), Sovereign (II), Accolade, Prodigy
®
, and Jetsetter
®
(J/JJ) SmartJet levers
are designed to operate in the 3 o’clock and 9 o’clock positions. The Sovereign (I) SmartJet lever has been designed to operate in the 3
o’clock, 6 o’clock, 9 o’clock, and 12 o’clock positions.
7. Set the temperature control to the desired temperature between 100°F and 104°F (36°C and 40°C), then place the vinyl cover on the spa and
allow the water temperature to stabilize (approximately 24 hours). Make sure you secure the cover in place using the cover locks. Periodically
check the spa water temperature. When the water temperature climbs above 90°F (32°C), proceed to the next step.
8. Rotate the SmartJet lever(s) to the primary position (3 o’clock) and turn on the CLEAN cycle for ten minutes to circulate the spa water. After the
clean cycle is complete, test the spa water for Free Available Chlorine (FAC) residual. If the residual is between 3 and 5 ppm on the test strips
(found in the test kit) go on to the next step. If the residual is less than 3 ppm, superchlorinate the spa water by adding 1-1/2 teaspoons of
chlorine (sodium dichlor) per 250 gallons (950 liters) of spa water. Use the jet button marked “CLEAN” to circulate the spa water for a ten-
minute period.
9. Rotate the SmartJet lever(s) to next position and let the spa water circulate (using the jet) for ten minutes. Test the spa water for Free Available
Chlorine (FAC) residual. If the residual is between 3 and 5 ppm on the test strips (found in the test kit) go on to the next step. If the residual is
less than 3 ppm, superchlorinate the spa water by adding 1-1/2 teaspoons of chlorine (sodium dichlor) per 250 gallons (950 liters) of spa
Operating Instructions
Summary of Contents for Hot Spring
Page 1: ...Owner sManual...