Page 14
O
PERATING
I
NSTRUCTIONS
SPA CONTROL PANEL
Your control panel consists of an LCD display and convenient touch
pads that allow you to set the water temperature and adjust the skim/
filter cycle settings, lock spa temp, lock all spa functions, as well as
control the hydrotherapy jets, and lights.
LCD DISPLAY INVERSION
You may invert the control panel display for easier viewing from inside
the spa. To invert the display the following is required: Press the
MODE(
T
) and (-) buttons simultaneously. By pressing the MODE(
T
)
and (-) buttons simultaneously a second time the screen will go back to
it’s original display.
Light Icon
Filter Cycle Icon
Jets Button
Light Button
Temperature
Down/Off
Temperature
Up /On
Mode
S
Power Icon
Sleep
Icon
Temp Ready
Icon
Filter Cycle 2
Icon
Filter Cycle
1 Icon
Jet Icon
Mode
T
MODE BUTTON
From the Home screen use the
MODE
(
S
or
T
) button to scroll to the
System, Clean, Audio (if your spa is equipped) and Tools screen. Press
the
(+)
button to enter into the sub screens.
TEMPERATURE CONTROL
The set temperature range is from 80°F (26°C)
to 104°F (40°C). Temperatures of any setting
may rise slightly depending on the current
use and condition of your spa, and on outside
temperature. Whenever power is disconnected
and then reconnected to the spa, the water temperature setting will
automatically return to the last temperature entered into the program.
To increase the set temperature, press the
(+)
button, once for each
degree of increase temperature desired. If you hold the
(+)
button down,
the set temperature will increase by one degree every half second.
To decrease the set temperature, press the
(-)
button, once for each
degree of decreased temperature desired. If you hold the
(-)
button down, the
set temperature will decrease by one degree every half second.
JET PUMP CONTROL
Pressing the
JET
button changes the jet pump functions,
depending on the number of presses:
• 1st press:
Two-speed jet pump runs on low speed
• 2nd press:
Two-speed jet pump runs on high speed
• 3rd press:
Jet pump is off
LIGHT - ON/OFF & INTENSITY CONTROLS
The light control uses four positions: High, Medium, Low, and Off. To
turn on the spa light, press the LIGHT button. This will place all lights
in the spa in the High, or maximum intensity position. When the lights
turn on, the light symbol will also illuminate on the control panel display.
Press the LIGHT button again to lower the intensity of the lights to the
Medium position. Press the LIGHT button again to lower the intensity
even more, placing the lights intensity in the Low position. Press the
LIGHT button one more time to shut the lights off. When the lights are
deactivated, the light symbol will also turn off.
If the lights are left on, they will automatically be turned off by the control
system after 6 hours of continuous operation. The light symbol on the
panel will also turn off when the lights are deactivated.
If the lights will not turn on, make sure SPA LOCK is deactivated. SPA
LOCK disables all the controls on the control panel (see following pages
for more information on SPA LOCK).
SYSTEM MODE
Your spa is equipped with a System Mode. This function will allow you
to conveniently turn the jet(s) on high speed and the lights on maximum
intensity at the same time.
To activate the System Mode, perform the following functions:
Press the MODE (
S
or
T
) button until
SYSON is displayed on the screen. Press
the
(+)
button to activate the SYSON mode
feature. The jets and light icons will remain
illuminated on the display until the system mode
is deactivated.
NOTE:
Once activated, the jet and light functions can still be changed
by pressing the JETS or LIGHT button.
To deactivate the System Mode, press the MODE (
S
or
T
) button until
the SYSON symbol is displayed on the screen. Press the
(-)
button to
deactivate.
CLEANING MODE
All spas are equipped with a “Cleaning” mode. When the mode is
activated, the jet pump in the first jet system will turn on and run for ten
minutes (used for water maintenance). To activate the “Cleaning" mode,
press the MODE (
S
or
T
) button several times until the CLEAN menu
is displayed. Press the
(+)
button to activate the CLEAN mode feature.
NOTE:
The jet icon will flash on and off while
the “Cleaning ” mode is active.
To stop the Cleaning Cycle before the ten
minutes is complete, Press the MODE (
S
or
T
) button several times until the CLEAN menu
is displayed on the screen then press the
(-)
button to deactivate.
NOTE:
Pressing the JETS button will also deactivate the clean cycle
and the jet icon will remain on and solid.
TOOLS MENU
The TOOLS menu is one of the main menus on the control panel. Within
the TOOLS menu are seven submenus, which consists of; Temp Lock,
Spa Lock, Light, Econ or Summer Timer, Filter 1, Filter 2, LCD and Exit.
To enter onto the TOOLS menu, scroll through the main menus using
the MODE (
S
or
T
) button until TOOLS is displayed. Press the
(+)
button to enter into the TOOLS submenu, use the MODE (
S
or
T
)
button to scroll through the submenus. Once the desired submenu is
displayed, press the
(+)
button to activate that submenu. To leave the
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
POWER
POWER
POWER
POWER
POWER
POWER
POWER
READY
F1
F2
POWER
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
POWER
POWER
POWER
POWER
POWER
POWER
POWER
READY
F1
F2
POWER
Operating Instructions
English
French
Spanish
