WaterLogic WL800 - MAX II Manual Download Page 11

Page: 11 / 74

WL800 Manual

Page 11 – Revision 12-11-2018

DISASSEMBLING AND REFITTING INSTRUCTIONS

Exercise Caution not to damage or deform any parts when disassembling the system.

Refit the system in the reverse order of disassembling.

Before disassembling the WL800 Water Treatment System

Block the main water by closing the main water supply valve.

Completely drain the water from the water tank.

If the water is splashed during the repair, insulation may deteriorate, resulting in danger.

Unplug the WL800 Water Treatment System.

When disassembling and refitting the unit with its side touching the ground, perform the job on a

working cloth. Without the working cloth, the product may get scratches.

Tools Needed:

•

Phillips Screwdriver

•

Flathead Screwdriver

•

Needle Nose Pliers

Summary of Contents for WL800 - MAX II











































































Search results

Summary of Contents for WL800 - MAX II

Reviews:

Related manuals for WL800 - MAX II

Brands by name

Popular brands

WaterLogic WL800 - MAX II, Manual

Search results

Summary of Contents for WL800 - MAX II

Reviews:

Related manuals for WL800 - MAX II

Brands by name

Popular brands