background image

 

WL400 

Manual                                                                                                                                    Page 53 – Revision: 7‐16‐2018 

      

WARNING!  

HOT CIRCUIT IS NOT SANITIZED.   

Water in the hot circuit is not sanitary until the temperature exceeds 171

°

F (77

°

C) for at least 5 

minutes. 

 

UV System Functional Test 
 

       

WARNING!

  

ULTRAVIOLET RADIATION.

  Protect your skin and eyes against ultraviolet rays.  

Never look directly at an operating UV light.  Disconnect wiring before removing. 

 

28.

 

Remove UV Firewall™ Lamp from Firewall™ housing.  Remove Top Cover from Firewall™ housing.  
Carefully remove Quartz Sleeve Spiral from Firewall™ Housing and inspect for cracks or other 
damage.  Reinsert Quartz Sleeve Spiral, replace top cover of housing.  Inspect UV lamp and 
reinsert into Housing. 
 

29.

 

Press Dispensing Button and check for blue glow from top of Firewall™ Housing and at Faucet 
dispensing area to ensure UV lamp is operational.  

 

30.

 

Disconnect UV lamp to test UV lamp sensor operation.  Unit 
should alarm and UV Icon on display will light. 

 
 
 
 

31.

 

Disconnect power to 

WL400

 

Water Treatment System.

 

 

32.

 

Reconnect UV lamp. 

 

33.

 

Connect power to 

WL400

 

Water Treatment System.

 

 

Compressor Test 
 

34.

 

Switch Green Heater/Compressor to on 

I=ON 

position.  Always ensure tanks are 

full of water before turning on the heater or the overloads (high limit) will open 
and require manual reset.  If the wire condenser at back of the unit is warm, the 
refrigeration system is working.    

 

 

 

35.

 

Once the 

WL400 Water Treatment System

 reaches its target temperature, the compressor will 

shut off.  Draw a glass of cold water and verify it is has been chilled to proper temperature. 

 

Heater Test 

Summary of Contents for WL400 Series















Reviews: