Waterboy MAXI ARRAY Installation Manual Download | Manualshive

Page: 10 / 20

background image

10

Beam

Place the Beam in the Tube Cap flanges and fasten with M16 All Thread and nut.

Angle Adjusters

Place the 2 x angle adjustment tubes between the beam and the tube cap, on the outside of each.
Fasten with the M16 All Thread and nuts once you select the angle desired (

see next page

). It is

recommended positioning the beam flat for assembly and adjusting for angle once complete.

«
...
8
9
10
11
12
...
»

Summary of Contents for MAXI ARRAY





















Reviews:

No comments

Related manuals for MAXI ARRAY

Brand: Icop Pages: 44

Brand: AXIOMTEK Pages: 51

Brand: Saia Burgess Controls Pages: 73

Brand: Conergy Pages: 30

Brand: Bongshin Pages: 45

Brand: Ecolibrium Solar Pages: 50

Brand: GRIDFREE Pages: 24

Brand: JETWAY Pages: 14

HPC-080SC-2807A Series

Brand: JETWAY Pages: 38

Brand: S-Energy Pages: 16

iXP2-08 A Series

Brand: LS Pages: 2

eXP20-20-TTA/DC

Brand: LS Pages: 2

ITP-E8000 Series

Brand: Savant Pages: 2

CleverTouch Gen.2

Brand: E3 Pages: 3

Polar Bear III HD 5 Degree

Brand: PanelClaw Pages: 27

XP-503-10-A10-A01-1B

Brand: Eaton Pages: 75

Brand: UNITED LINK Pages: 111

HARMAN AMX VARIA-80

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands