-1-
What You’ll Need
Before You Start
INSTALLATION MANUAL FOR WATER PRESSURE BOOSTER
Please read the following instructions carefully
Keep this manual with the tank for future reference.
Part #: 9077-0014 (01/19)
Recommended Tools
Adjustable Wrench
Adjustable Pliers
Pipe Wrench
Tubing Cutter
Screwdriver
Tape Measure
Tire Pressure Gauge
NPT Male Adapters: 1
¼
" & 1"
100 psi Relief Valve
Spring Loaded Check Valve
Drain Valve
Shutoff Valves
Wire Connections Line
Teflon
®
Tape
Additional Parts Required (Not Included)
USE ONLY WITH POTABLE WATER
SYSTEMS.
Do not operate in a setting with
freezing temperatures or where the temperature can exceed
100°F and do not exceed the maximum working pressure
specified for this Product.
READ
CAREFULLY
THE
PRODUCT
INSTALLATION
&
OPERATION
INSTRUCTIONS. FAILURE TO FOLLOW THE INSTRUCTIONS
AND WARNINGS MAY RESULT IN SERIOUS OR FATAL INJURY
AND/OR PROPERTY DAMAGE, AND WILL VOID THE PRODUCT
WARRANTY. THIS PRODUCT MUST BE INSTALLED BY A
QUALIFIED PROFESSIONAL. FOLLOW ALL APPLICABLE
LOCAL AND STATE CODES AND REGULATIONS. IN THE
ABSENCE OF SUCH CODES, FOLLOW THE CURRENT EDITIONS
OF THE NATIONAL PLUMBING CODE AND NATIONAL ELECTRIC
CODE, AS APPLICABLE.
This Product, like most Products under
pressure, may over time corrode, weaken and
burst or explode, causing serious or fatal injury, leaking or
flooding and/or property damage. To minimize risk, a licensed
professional must install and periodically inspect and service the
Product. A drip pan connected to an adequate drain must be
installed if leaking or flooding could cause property damage. Do
not locate in an area where leaking could cause property damage
to the area adjacent to the appliance or to lower floors of
the structure.
This product can expose you to chemicals
including lead, which is known to the State of
California to cause cancer and birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
RUPTURE OR EXPLOSION HAZARD.
Do not
expose Product to freezing temperatures or
temperatures in excess of 100°F. Do not adjust the precharge or
re-pressure this Product except during installation or regular
inspection. Replace the Product and do not adjust the precharge
if corroded, damaged or with diminished integrity. Adjustments
to precharge must be done at ambient temperature only. Failure
to properly size the Product or follow these instructions may
result in excessive strain on the system and may lead to Product
failure, serious or fatal personal injury, leakage and/or
property damage.
A 100 psi relief valve must be installed to
prevent excess pressure. At least once every 3
years or if discharge is present, a licensed contractor should
inspect the pressure relief valve and replace if corrosion is evident
or the valve does not function.
FAILURE TO INSPECT THIS
VALVE AS DIRECTED COULD RESULT IN UNSAFE PRESSURE
BUILD-UP WHICH CAN RESULT IN PRODUCT FAILURE, SERIOUS
INJURY OR DEATH AND/OR SEVERE PROPERTY DAMAGE AND
VOID THE PRODUCT WARRANTY.
Chlorine & Aggressive Water:
The water
quality can significantly influence the life of
this Product. You should test for corrosive elements, acidity, total
solids and other relevant contaminants, including chlorine and
treat your water appropriately to insure satisfactory performance
and prevent premature failure.
NOTE:
Inspect for shipping damage. Notify freight carrier or store where purchased immediately if damage is present. To avoid
risk of personal injury and property damage, if the product appears to be malfunctioning or shows signs of corrosion, call a qualified
professional immediately. Current copies of the product manual can be viewed at www.amtrol.com. Use proper safety equipment
when installing.
THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL PERSONAL INJURY AND OTHER
HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL TO REDUCE THE RISK OF PERSONAL INJURY AS
WELL AS PROPERTY DAMAGE.
