background image

STARTING UP THE SYSTEM

7

 

Check all connections to make sure the system has no leaks. Once you’ve verified all  

 

stages of regeneration are working appropriately, and have verified there are no    

 

leaks, fill the brine tank with sodium chloride or potassium chloride softening pellets.

Step 3. 

To ensure sanitary conditions in the mineral and brine tanks, place 1.5 ounces of   

 

common household bleach into the brine tank. Press and hold the REGEN button for 3  

 

seconds to move the control valve into regeneration sequence. Allow the FILL cycle to  

 

complete (5-8 min). Then press the REGEN button to allow the motor to move to the  

 

“SOFTENING” position and then push REGEN again, moving system to “DRAW”    

 

position. This cycle normally takes about 60 minutes; however, 15 minutes should be  

 

sufficient to pull the chlorine from the brine tank. After 15 minutes, press and hold   

 

the REGEN button to move the control valve to the “BACKWASH” position. Let the   

 

valve complete this cycle, and also the “RINSE” cycle, which will come next. Once the  

 

valve has completed the “RINSE” cycle, it will automatically return to “SOFTENING”.  

 

In step 5, you will set the valve to “Regen Today” so that it will regen the night after  

 

install at the specified time. If there is any residual chlorine, it will be removed during  

 

that regeneration.

Step 4. 

Make sure that the bypass valve is completely set in the “Normal Operation”  

 

 

position. Let the water in the taps of the building run for several minutes to purge the  

 

unconditioned water out of the pipes. After several minutes, take a water sample and  

 

test for hardness from the running tap. If a hardness test reads “soft” water, the    

 

installation is correct.

Step 5.

 Press and release the REGEN button. You should see “Regen Today” appear on the  

 

LCD screen. This will instruct the control valve to regenerate tonight at the specified  

 

time (usually 2:00 am).

Step 6.

 Drain hot water heater and let it refill with conditioned water. We suggest draining  

 

the hot water by turning on the hot water taps in the house. We recommend doing  

 

this just prior to bedtime.

Summary of Contents for Reionator Pro Ultra RXU13

















Reviews: