Important Tips:
•
Store your Pool Blaster in a clean, dry place when not in use. Do not leave it under-
water, in direct sunlight, or exposed to extreme heat or cold.
•
You may clean the Pool Blaster body with soap and water. Avoid using solvents
when cleaning plastic parts. Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged by their use. Use clean cloths to
remove dirt, dust, oil, grease etc.
•
The On-Off knob should be periodically lubricated with a silicon-based grease.
CAUTION:
Do not at any time let brake fluids, gasoline, petroleum-based products,
penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage,
weaken, or destroy plastic
.
WARNING:
Do not attempt to modify this tool or create accessories not approved for
use with this tool. Any such alteration or modification is misuse and could result in a hazardous
condition leading to possible serious injury. The batteries and motor are factory sealed in the
motor box, and CANNOT BE REPLACED. Do not attempt in any way to destroy or disassemble
motor box or any of its components. Instead, take your Pool Blaster to an authorized service
center. Failure to follow these instructions may void your warranty agreement.
•
General maintenance of your Pool Blaster requires you occasionally clean off the O-
rings on the “ON-OFF” knob and add silicone lubricant/sealant. This will ensure easier
turning and a water-tight seal. This lubricant is available at your local pool & spa retailer.
•
In the Nose Cap (Part No. PBA002) there is a Flapper Valve. To keep the Nose Cap
Flapper Valve moving freely, clean the valve after every use. This will help to keep
dirt inside the Pool Blaster after the cleaner is removed from the pool.
Service Information
NOTE:
Any repairs requiring disassembly must be performed by a Water Tech Authorized
Service Center. For the repair center nearest you call us toll free at 1-800-298-8800. Unauthor-
ized repairs will void the warranty.
Storing the Pool Blaster
NOTE: State of the art Nickel-Metal Hydride batteries power the Pool Blaster. These are the
same batteries used in many portable phones. In order to properly ventilate and cool the bat-
teries and drive system a certain amount of space is left open in the Pool Blaster body. As a
result, from time to time, water may enter the unit. In order to allow for any water to be drained
you should remove the On-Off Knob after each use, turn the machine so the knob is towards the
floor and tilt side to side in all directions. The amount of water may be very small or not noticed
at all. After removing any water use a blow dryer on warm setting to dry any moisture build-up on
the inside of the motor box. Water entering the Pool Blaster body presents no safety hazard and
should be drained to avoid any chance of long-term corrosion. . The batteries and motor in the
Pool Blaster are long lasting and proper care will help to prolong the life of your appliance.
NOTE:
Remove Pool Blaster from charger before storage.
When not in use, your Pool Blaster should be stored indoors, in a clean dry location sheltered
from direct sunlight, extreme temperatures and rain. Do not store the Pool Blaster in a garage
or anywhere the unit could freeze. Storing the Pool Blaster in areas of high humidity can affect
battery performance over time.
For your convenience the Pool Blaster has an oval opening in the pool pole adaptor on which you
can hang the unit.
Long Term Storage
Follow the above storage instructions and unplug the charger from the electrical outlet.
When charging for the first time after long-term storage, your Pool Blaster may take 2-3 uses
before full time is achieved.
Water Tech warrants this product for one year against any defects in material or workmanship under normal use and
service, subject to conditions and limitations as described below.
Parts not covered under warranty: The filter bag, nose cap, vacuum head, wheels and brushes are not warranted parts
as these items require replacement in the normal course of use, due to normal wear.
This warranty covers only normal use for a residential swimming pool or spa. Damage, defect, malfunctions or any use,
which does not comply with the operator instructions, are excluded. Damage or any failure caused by repair, which is
done by anyone other than a Water Tech authorized service center, shall not be covered.
The motor housing is a factory sealed unit. The warranty will be considered void if opened
by a non-authorized service center.
To validate this warranty: The enclosed WARRANTY REGISTRATION CARD must be mailed within ten days of
purchase. No warrant service will be performed unless Water Tech has received the WARRANTY REGISTRATION
CARD.
The warranty obligations of Water Tech shall be limited to repair or replacement of the product. Water Tech, Inc shall
not be liable or responsible under any circumstances or in any amount for consequential or incidental damages, or for
injury or damages to persons or property using or used in connection with the product or for loss of profits or other costs
or expenses of any kind of character. There are no other warranties or representations by Water Tech other than as set
forth herein, either expressed or implied and no person, firm or corporation is authorized to make any representation or
incur any obligation in the name or on behalf of Water Tech except as stated herein.
WARRANTY
MAINTENANCE
