Water Ace RSP10 Installation Manual Download Page 2

2

23833A157

IMPORTANT INSTRUCTIONS BEFORE INSTALLATION

Failure to follow these instructions may cause serious bodily injury and/or property damage.

Save this manual for future reference. 

This is the safety alert symbol.

 When you see this symbol 

on your pump or in this manual, look for one of the following 
signal words and be alert to the potential for personal injury:

DANGER 

warns about hazards that 

will

 cause serious personal 

injury, death or major property damage if ignored.

WARNING 

warns about hazards that 

can

 cause serious personal 

injury, death or major property damage if ignored.

CAUTION 

warns about hazards that 

will

 or 

can

 cause minor 

personal injury or property damage if ignored.
The label

 NOTICE 

indicates special instructions which are 

important but not related to hazards.

Carefully read and follow all safety instructions in this manual 

and on pump.

Keep safety labels in good condition. 
Replace missing or damaged safety labels.

WARNING. Severe personal injury or death could result from 

improperly sizing the pump, or from using it for any purpose 

other than as an in-ground pool pump.

 Hazards may include, 

but are not limited to, electrical shock, fire, flooding, suction 
entrapment, or structural failure of the pump or other system 
component.

WARNING. Pressure testing hazards.

•  Do not allow people to work around components under test.
•  Post appropriate warnings and barriers around pressurized 

equipment.

•  Test for the minimum time allowed by local codes.
•  If the equipment is located in a separate room, close and lock 

the door and post warning signs.

ELECTRICAL

This pump must be wired through a Ground Fault Circuit 
Interrupter (GFCI) to protect the circuit. To reduce the risk of 
electrical shock, connect the green terminal on the pump to the 
grounding terminal of your electrical service or supply panel. Use 
a conductor at least as large as the wires conducting power to the 
pump. Refer to local or national codes for details.
Installations must comply with the National Electrical Code or the 
Canadian Electrical Code, as applicable, and all applicable local 
codes and ordinances.

GENERAL

Pool main drain installation must comply with current local and 
national building, electrical, plumbing and pool/spa codes, as 
applicable.
Prime the pump (fill the pump and piping system with water) 
before starting it for the first time. If you do not get satisfactory 
circulation within 5 minutes, stop the pump and reprime it. Do 
not allow the pump to run for an extended period of time with no 
water moving. In these conditions, the pump may overheat and 
start a fire or possibly explode.

WARNING. Explosion hazard, with risk of severe 

injury or death.

 Always stop the pump and relieve all 

pressure in the system before adjusting or releasing 

any fastenings. Make sure there is no air in the system (use the 
air bleed valve on the pool filter to  release any trapped air in the 
system). NEVER adjust, loosen or tighten any lid clamps or bolts 
while the system is pressurized.

WARNING. Risk of electrical shock – can burn or 

kill. 

Always disconnect power to the pump at the 

circuit breaker before servicing or working on the 
pump. Make sure that no one can connect the power 

without your knowledge and consent.

WARNING. Fire and burn hazard.

 Do not allow leaves 

and debris to collect around the pump. Do not allow 
children around the pump and filter areas. Allow the 
pump motor to cool for 20 minutes before working  
on it.

DANGER. Hazardous Suction. Can trap hair or body, causing 

severe injury or death.

•  Do not block circulation pump suction. MAKE SURE that all main 

drains are correctly installed, with anti-entrapment covers, 
listed to ASME A112.19.8, screw-fastened in place, and that 
any vacuum outlets are protected by self-closing, self-latching 
vacuum covers listed to IAPMO SPS-4 2000.

•  Keep small children under close adult supervision around the 

pool at all times.

•  NEVER allow anyone (adult or child) to sit on a pool main drain.
•  Very small children sometimes think that a main drain is really 

a place to “go potty”. Don’t let them do this!

B

od

y

F

or

eA

rm

Upp

er

Arm

Leg Jo

int

Leg

 J

oi

nt

Leg 

Joi

nt

Leg

 Jo

in

t

Summary of Contents for RSP10

























Reviews: