WA483
2
DESCRIPTION
Water Ace Sink Pump System, Model Number R1030, is ideal
for home wastewater removal from beautician or utility sinks
and wet bars, and for drain water transfer from air condition-
ers or dehumidifiers.
1/3 HP submersible pump unit is equipped with a 3-prong
grounding-type power cord. Motor is oil-filled (dielectric oil)
and sealed for cooler running. Upper sleeve/lower ballbearing
on motor shaft never need lubrication. Automatic reset ther-
mal protection.
SPECIFICATIONS
Power supply required ......................................115V, 60 Hz.
Liquid temp. range..........................................32° to 130°F
Individual branch circuit required (minimum)............15 Amps
Discharge ..........................................................1-1⁄2" NPT
UNPACKING AND INSPECTION
Handle with care. Check items received against packing list to
be sure that all equipment has been received. Inspect for
shipping damage. If found, file claim with carrier immediately.
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give many years of
trouble-free service when correctly installed, maintained, and
used. However, unusual circumstances (interruption of power
to the pump, dirt/debris in the sump, flooding that exceeds
the pump’s capacity, electrical or mechanical failure in the
pump, etc.) may prevent the pump from functioning normally.
To prevent possible water damage due to flooding, consult
your dealer about installing a high water alarm. See the
“Troubleshooting Chart” in this manual for information about
common sump pump problems and remedies. For more infor-
mation, see your dealer or call customer service.
1. Know the pump application, limitations, and potential
hazards.
2. Disconnect power before servicing.
3. Release all pressure within system before servicing any
component.
4. Drain all water from system before servicing.
5. Secure discharge line before starting pump. An unsecured
discharge line will whip, possibly causing personal injury
and/or property damage.
6. Check hoses for weak or worn condition before each use,
making certain that all connections are secure.
7. Periodically inspect system components. Keep free of
debris and foreign objects. Perform routine maintenance as
required.
8. Provide means of pressure relief for pumps whose discharge
line can be shut-off or obstructed.
9. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep work area clean, uncluttered and properly lighted
– replace all unused tools and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks, master
switches, and by removing starter keys.
10. When wiring an electrically driven pump, follow all electri-
cal and safety codes that apply.
11. This equipment is only for use on 115 volt (single phase)
and is equipped with an approved
3-conductor cord and 3-prong, grounding-type plug.
To reduce risk of electric shock, pull plug
before servicing.
This pump has not been investigated for use
in swimming pool areas. Pump is supplied with a grounding
conductor and grounding-type attachment plug. Be sure it is
connected only to a properly grounded grounding-type recep-
tacle. Where a 2-prong wall receptacle is encountered, it must
be replaced with a properly grounded 3-prong receptacle
installed in accordance with codes and ordinances that apply.
12. All wiring should be performed by a qualified
electrician.
13. Make certain power source conforms to requirements of
your equipment.
PERFORMANCE
SPECIFICATIONS
Motor
Full Load
Switch Setting
Top
Bottom
HP
Amps
On
Off
Height
Width
Width
Weight
1/3
9.8
7"
2"
13-3/4"
15-1/8"
12"
32 lbs.
GPM of Water @ Total Feet of Head
Model
HP
5’
10’
15’
20’
Shutoff
R1030
1/3
48.0
40.0
29.0
15.0
24’
Summary of Contents for R1030
Page 23: ...23 WA483 ...
