•
Design and specifications are subject to change without notice.
•
Watec is not responsible for any inconvenience or the attendant damages
to the video and monitoring recording equipment caused by misuse, mis-
operation or improper wiring of our equipment.
•
If for any reason the
W-01CDB3
does not work properly, or if you have
any questions regarding installation or operation, please contact the
distributor or dealer from which it was purchased.
1353Z00-Y2100002
Be careful not to touch the other terminal while wiring. Protect the wiring
portion by using insulation tape after wiring. If the above care and attention
is not adhered to, damage to the
W-01CDB3
and power adaptor may
occur or may cause fire.
Auto-iris Lens
There are two output terminals on the W-01CDB3.
One for Video auto-iris lenses and one for DC
auto-iris lenses. Please pay attention to the correct
wiring configuration, as shown in the figure on the
right.
NB. Damage will occur if the correct wiring
configurations are not adhered to.
Mounting Holes
As shown in the figure on the right. The W-01CDB3
provides four mounting holes, one in each corner of the
circuit board. Fix the unit securely using M2 screws.
Once the board is secured proceed with the following
steps below.
Set-up and Operation
1) Ensure that the power to the
W-01CDB3
and the peripheral
equipment is turned off before making any connections.
2) Remove the lens mount cap from the
W-01CDB3
and attach the
CS-mount lens. Use the optional C-mount adaptor (34CMA-R) when a
C-mount lens is used.
3) Connect the iris cable to the
W-01CDB3 as shown above in
【
Auto-iris Lens】section, when an auto-iris lens is being used.
4) Connect the attached cable to ⑨POWER IN/VIDEO OUT. See the
【Power Supply and Wiring】section.
5) Connect a coaxial cable with 75Ω impedance, such as an RG-58/U or
an RG-6/U to the monitor. Select a monitor with the same television
system as the
W-01CDB3
: NTSC or PAL. A monitor with more than
500TV lines is recommended.
6) Turn on the power to the
W-01CDB3
, monitor and all other allied
equipment. When a picture cannot be obtained on the monitor, or a
strong smell of burning is present, or smoke is visible, check and follow
the procedure mentioned in the Problems and Trouble Shooting section.
7) Focusing: Follow the operations mentioned below while looking at the
screen on the monitor. When focusing is not possible, loosen
③
FOCUSING ADJUSTMENT SCREWS with the hexagonal wrench, then,
move the
②
LENS MOUNT backwards or forwards to focus.
Manual Lens
Adjust the focus and iris to the best position
on the lens.
Video Auto-iris Lens
Adjust the focus on the lens.
DC Auto-iris Lens
Adjust the iris level on the camera, then
adjust the focus on the lens. See below.
※When an auto-iris lens is used, set ⑦AE MODE CONTROL SWITCH to
ON and select any required shutter speed. (recommended shutter
speed setting is position 0 or 1)
8) Select any required shutter mode by ⑦AE MODE CONTROL SWITCH to
suit your preferences. When electronic iris (OFF) is selected, the shutter
operation is automatically stepped in a range between 1/60-1/100000
(NTSC), 1/50-1/100000(PAL). When electronic shutter (ON ) is
selected, select any required shutter speed from ⑧SHUTTER SPEED
CONTROL SWITCH.
9) Select any required shutter speed by the ⑧SHUTTER SPEED CONTROL
SWITCH to one of its 10 positions.
Shutter Speeds (Sec.)
No. Mode
NTSC PAL
0 OFF
1/60
1/50
1 FL
1/100
1/120
2 ES
1/250
3 ES
1/500
4 ES
1/1000
5 ES
1/2500
6 ES
1/5000
7 ES
1/100000
8 ES
1/200000
9 ES
1/500000
11) Set the ⑩FUNCTION SWITCHES according to your requirements.
Switch
Setting
Effective Condition (Example)
ATW
【1=OFF】
【2=OFF】
Automatically follows and adjusts to the
changing color temperature of the
illumination.
3200K
【1=OFF】
【2=ON】
Color correction to give natural color
renditions under incandescent lighting.
5100K
【1=ON】
【2=OFF】
Color correction to give natural color
renditions under bluish fluorescent light.
1. & 2.
White
Balance
8200K
【1=ON】
【2=ON】
Color correction to give natural color
renditions under bluish fluorescent light
more than 5100K.
ON
When a mirror image such as back
monitoring of a car is required.
3.
Mirror
Image
OFF
When a normal image is required.
ON
【100】
When dark areas on an object with
contrasting light and dark area are
monitored.
4.
Video
Level
OFF
【75】
When a standard video output level is
required
Specifications
Model
W-01CDB3 (NTSC)
W-01CDB3 (PAL)
Pick-up Element
1/3 inch interline transfer CCD image sensor
Number of
Total Pixels
811(H)×508(V) 795(H)×596(V)
Number of
Effective Pixels
768(H)×494(V) 752(H)×582(V)
Unit Cell Size
6.4um(Ｈ)×7.5um(V)
6.5um(Ｈ)×6.3um(V)
Scanning System
2:1 interlace
Sync. System
Internal
Video Output
Composite video, 1.0V(p-p) 75Ω (Unbalanced)
AGC 3〜24dB
Back Light
Compensation
Full-screen
Resolution (H)
450TVL (Center)
Minimum
Illumination
1.5 lx. F1.2
S/
N
50dB
Gamma
Characteristics
γ≒0.45
EI
1/60〜1/100000 sec.
1/50〜1/100000 sec.
AE
Mode
ES
1/60(50)、1/100(120)、1/250、
1/500、1/1000、1/2000、1/5000、
1/10000、1/20000、1/50000 sec.
Power Supply
DC12V±10%
Power
Consumption
1.2W (=100mA)
Operating
Temperature
-10〜40℃
Operating Humidity
Less than 95% RH (Without condensation)
Storage
Temperature
-30〜70℃
Storage Humidity
Less than 95% RH (Without condensation)
Size 42(W)×42(H)×20.7(L)
(mm)
Lens Mount
CS-mount
Weight 35g
/
Contact information
Watec Co., Ltd.
Add.:
254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,
Yamagata-Ken, 997-0017 Japan
/
TEL: +81-235-23-4400 FAX: +81-235-23-4409
/
Email:
URL: http://www.watec.net
Red: DC+12V
Black: Common GND
Blue: Video out
To power supply （DC+12V ）
Black: Common GND
To power supply （GND ）
To 75Ωcoax. cable
for monitor
All manuals and user guides at all-guides.com
