Wassp WMB-X230, Installation Manual

Page: 10 / 18

Page 18 of 34 Page 19 of 34 Doc: Transducer Installation
Version: 2.6 May 2021
Doc: Transducer Installation
Version: 2.6 May 2021
wassp.com wassp.com
TRANSDUCER INSTALLATION MANUAL TRANSDUCER INSTALLATION MANUAL
Tighten the nuts indicated by "4" to a torque of 1.5-2Nm.
If any gaps exist between the transducer body "6" and the mounting frame "1" they
will need to be filled by a water proof 24hr cure epoxy.
All measurements are nominal. Check measurement of the actual transducer.
4
4
4
6
1
5.3. WIDEBAND FAIRING TRANSDUCER 90-190KHZ MOUNTING
Part List (WSP-002-133 & WSP-002-134)
ITEM QTY PART DESCRIPTION
1 1 Fairing Block Optional
2 2 Threaded rod Optional: M12
3 2 Locking nut Optional: M12 Nyloc
4 6 Washer Optional: M12
5 6 Nut Optional: M12
Not included:
- Mounting tools
- Marine sealant
392
15.40
32.70
110
A A
524
7
166.50
207
184
202.50
281
SECTION A-A
REV. DESCRIPTION DATE UPDATED BY CHECKED BY
01 INITIAL RELEASE 29-01-2020 ALEXANDRA OETZEL CRAIG SHANNON
GENERAL TOLERANCES UNLESS OTHERWISE SPECIFIED (MEDIUM)
≤3 >3-6 >6-30 >30-120 >120-400 >400-1000 >1000-2000
0.1 0.1 0.2 0.3 0.5 0.8 1.2 1.0
GENERAL TOLERANCES UNLESS OTHERWISE SPECIFIED (FINE)
≤3 >3-6 >6-30 >30-120 >120-400 >400-1000 >1000-2000
0.05 0.05 0.1 0.15 0.2 0.3 0.5 0.5
GENERAL TOLERANCES UNLESS OTHERWISE SPECIFIED (COARSE)
≤3 >3-6 >6-30 >30-120 >120-400 >400-1000 >1000-2000
0.2 0.3 0.5 0.8 1.2 2.0 3.0 2.0
F
E
4 2
1 7
5
3
8 6
B
C
D
A
1 OF 1 A3
CHECKED BY
DESCRIPTION PART NUMBER
REVISION
DRAWN BY
PC
MATERIAL
Fairing
SHEET SIZE
DATE
200600
29-01-2020 Alexandra Oetzel Craig Shannon
B
C
D
E
F
A
1
8
6 7 5 4 3 2
GENERAL NOTES:
PART MUST BE CLEAN WITH NO SINKS, FLASH, SHARP EDGES OR BURRS. 1.
ALL DIMENSIONS ARE IN MILLIMETRES UNLESS OTHERWISE SPECIFIED. 2.
ALL DIMENSIONS AND TOLERANCES TO APPLY AFTER FINAL TEXTURING 3.
AND SURFACE FINISHING.
REFER TO CAD DATA FILE (200600.IGES/.STEP/.X_T) FOR MISSING 4.
DIMENSIONS.
UNLESS OTHERWISE STATED, ONLY USE RoHS COMPLIANT MATERIAL. 5.
This document contains confidential and proprietary information and rights that belongs to Electronic Navigation Ltd. Using, or permitting the use of, any of the information
contained herein, copying or imaging all or part of this document by any means, or permitting any such copying or imaging, or disclosing, or permitting the disclosure of,
any of its content to third parties is strictly forbidden without express written consent of Electronic Navigation Ltd. ©2019 Copyright Electronic Navigation Ltd.
CLIENT
Electronic
Navigation FINISH
Black
COLOUR
Smooth
IF YOU OVERRIDE DIMESNIONS OR LINKS PLEASE MAKE A NOTE OF THIS OFF SHEET
STANDARD DRAWING NOTES (DELETE/ADD AS NEEDED):
PLASTIC PARTS:
SHEET METAL PARTS:
NOTES UNLESS OTHERWISE SPECIFIED:
NOMINAL DRAFT ANGLE: XX° 1.
NOMINAL WALL THICKNESS: XXmm 2.
ALLOWABLE FLASH: ±X.XXmm 3.
TRIM GATE: ±X.XXmm 4.
EJECTOR MARKS: ±X.XXmm 5.
CORNERS MOUDLED SHARP: RX.X MAX 6.
PART IDENTIFICATION: 7.
a. MOLD CAVITY NUMBER: 0.15mm RAISED
b. PART NUMBER: 0.15mm RAISED
c. PLASTIC GENERIC IDENTIFIER THIS AREA:
i. “PC/ABS”, FONT: ARIAL, 3mm HEIGHT, 0.15mm RAISED
ii. SPI ‘TRIANGULAR’ RESIN IDENTIFICATION CODE: 1… 7
d. DATE WHEEL FOR MONTH / YEAR
MACHINED PARTS:
NOTES UNLESS OTHERWISE SPECIFIED:
1.
NOTES UNLESS OTHERWISE SPECIFIED:
1.
NOTES UNLESS OTHERWISE SPECIFIED:
1.
ASSEMBLIES: