background image

Safety Instructions 

 

WARNING 

Equipment contains dangerous voltages and can be hazardous if installed or 

operated incorrectly. Non-compliance with 

Warnings

 or failure to follow the 

instructions contained in this manual can result in loss of life, severe personal 
injury or serious damage to property.  

 

Installation 

 

Use qualified, skilled personnel 

 

Follow installation instructions 

 

Connect to correct voltage and supply current 

 

Provide fully accessible Electrical Isolation Switch & water supply valves 

 

Training and Supervision 

 

Read and Understand the Operating instructions and train all staff 

 

This appliance must not be operated by children or infirm persons 

 

Machine panels must only be removed by suitably qualified and trained 

personnel – internal hazards include live electrics and very hot surfaces 

 

This appliance is not intended for use as a stepladder 

 

Hot Surfaces 

 

Some surfaces may be hot or very hot 

 

Chemicals 

 

Commercial dishwashing detergents are hazardous – handle with care 

 

Read  and follow the safety information found on the labels of detergent 

containers and Material Safety Data Sheets  

 

Use protective eyewear and clothing if decanting containers 

 

Hot Water 

 

Do not put hands in wash water which may be over 60°C and contain 
hazardous caustic detergent 

 

Rinse water can be over 90°C 

 

Door safety switches are designed for emergency use only 

 

Cleaning 

 

Do not hose down the machine or splash water over the exterior 

 

Watch for broken glass etc when cleaning the inside of the machine 

 

Power Cord Replacement 

 

If the supply cord is damaged, it must be replaced by the manufacturer 

or its service agent or a similar qualified person in order to avoid a 
hazard 

 

Service Manual XP-2

4

Revision 1C

Summary of Contents for XP









































Reviews: